Jenn-Air Range / Cooktop / Oven Wire, Harness, Power Cord

This replacement dryer power cord supplies electricity from your wall outlet to the dryer's terminal block, providing a secure, reliable connection. Replace a worn or damaged cord to restore dependable power and reduce risk of intermittent shutoffs.

• Supplies electrical power from the outlet to the dryer
• Provides a secure connection at the plug and the dryer's terminal block when properly installed
• Common fixes: dryer won't power on, power cuts out when the unit is moved, or visible damage/heat discoloration on the cord or plug
• Replace if prongs are loose or the insulation is cracked or melted

• Disconnect power at the breaker before servicing and verify the outlet is de-energized
• Follow the dryer's wiring diagram; connect conductors to the correct terminals and tighten securely
• Use an approved strain relief/clamp per the dryer instructions and local electrical codes

This contact assembly restores a reliable electrical connection within an appliance's control circuit. Replacing worn or pitted contacts helps eliminate intermittent operation and arcing so the controlled component can turn on and off consistently. What it does

• Provides the conductive interface that completes the circuit when the control is engaged
• Helps deliver stable power to the connected load
• Typical failure signs: intermittent operation, no operation of the controlled component, visible heat damage/pitting on contacts, arcing or buzzing at the contact point

• 1 contact assembly

• Disconnect power to the appliance before servicing and verify no voltage is present
• Access the control area; photograph or label wire positions and terminal orientation
• Move wires one at a time to the new assembly; ensure tight, clean connections
• Inspect nearby wiring for heat damage and replace any burnt terminals; test operation before reassembly

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

This wire harness assembly routes power and signals between major components to restore electrical connection and reliable operation. It replaces a damaged or frayed harness to help eliminate intermittent power, no-starts, or lost control functions. What it does:

• Connects power and control circuits between the main control and other components
• Restores reliable electrical continuity when wiring is damaged, burned, or corroded
• Helps resolve symptoms such as intermittent operation, appliances that won't start, or components that receive no power
• Prevents shorting or arcing caused by exposed or broken wires when properly installed

• Disconnect the appliance from power (unplug or turn off the circuit breaker) before beginning work
• Handle connectors gently; match keyed connectors when reassembling to avoid miswiring
• Inspect mating terminals and housings for damage; replace if terminals are burned or corroded

This multi-wire electrical harness routes power and signals between appliance components to restore reliable connectivity and control. Replacing a damaged harness helps stop intermittent operation and prevents wiring shorts or lost function. What it does:

• Carries power and control signals between components such as controls, motors, sensors, or switches
• Restores electrical continuity when original wiring is frayed, cut, or burned
• Helps stop intermittent operation, no-start conditions, or component failures caused by damaged wiring
• Prevents potential short circuits from exposed or chafed wires

• Disconnect power before starting — always follow lockout/tagout procedures
• Replace harness using routing and connector orientation
• Inspect mating connectors and terminals; do not use if corrosion or damage is present
• Securely fasten harness with existing clips/ties to avoid rubbing or heat exposure

The Harness-Wire is an OEM part for Whirlpool ranges. It serves as the wiring harness that connects electrical control boards and sensors within the range. 

 Symptoms of a bad harness-wire include:

• Elements or burners that do not heat 
• Issues with switches, controls, or displays failing to work properly
• Recurring range or oven component malfunctions

Causes of a bad harness-wire can be damage from excessive flexing/bending over time, moisture leading to shorts, or failure of crimp/solder connections along the wire.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes power and signals between appliance controls and electrical components to restore reliable operation. Replaces a damaged, frayed, or burnt harness to help eliminate intermittent or lost power to components. What it does:

• Carries electrical power and control signals between the control board and motors, switches, sensors, or heating elements
• Restores consistent electrical connections when original wiring is damaged, corroded, or pinched
• Addresses symptoms such as components not powering on, intermittent operation, blown fuses, or visible burn/damage at wiring
• Prevents shorting and arcing caused by exposed or broken conductors when replaced promptly

• One wire harness as pictured and specified by the manufacturer

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Match connector shapes and pin counts; route harness clear of sharp edges, heat sources, and moving parts
• Use only the exact replacement harness to maintain proper connector fit and circuit protection
• If you see burned connectors, melted insulation, or a repeatedly tripped breaker, inspect related components and replace damaged parts as needed