Jenn-Air Refrigerator Gasket & Seal

This freezer door gasket replaces a worn or deformed seal to restore a tight, even closure on the freezer door. A proper seal keeps cold air in and humid air out, reducing frost buildup and temperature swings.

• Creates an air-tight seal between the freezer door and cabinet to contain cold air
• Helps maintain correct temperature and efficiency; reduces frost/ice around the door perimeter
• Symptoms of failure: tears, cracks, warping, gaps, or door not closing fully
• Presents as frost buildup, moisture/condensation, or warm spots in the freezer

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax (lay flat; warm gently with hot water or a hair dryer) for easier fit
• Remove the old gasket from the retainer/channel; on screw-retained styles, loosen (do not remove) liner screws as needed
• Seat the new gasket evenly, starting at the corners; use gentle heat to smooth wrinkles and ensure a uniform seal all around

This is the front seal for the refrigerator's crisper compartment. It restores a tight barrier at the drawer's front edge so the crisper closes flush and maintains proper humidity to help keep produce fresh.

• Seals the front edge of the crisper to limit air leaks between the drawer and fresh food compartment
• Helps maintain intended humidity levels inside the crisper
• Restores smooth, flush closure of the drawer front
• Replace if the seal is torn, deformed, or missing; symptoms can include excess condensation or wilting produce

• Unplug the refrigerator and remove the crisper drawer
• Pull the worn seal off the crisper front/channel and clean the mating surface
• Warm the new seal in hot water to improve flexibility; press it evenly into place and ensure corners are fully seated
• Reinstall the drawer and verify proper alignment and closure

This refrigerator door gasket for foam-in-place doors creates a tight seal around the door opening to keep cold air in and moisture out, helping maintain stable temperatures and reduce frost and energy waste.

• Seals the door perimeter to prevent warm air leaks
• Helps maintain correct cooling performance and humidity levels
• Reduces frost and condensation caused by poor sealing
• Common signs it's needed: tears, warping, gaps, persistent frost/condensation, door not sealing or popping open

• Disconnect power before servicing
• Warm and relax the gasket in hot water or with a hair dryer on low to ease installation
• Remove the old gasket from the retainer/channel; install the new gasket starting at the corners and press fully into place
• Check the seal all around and adjust the door/hinges as needed; allow time for the gasket to set

This rear icebox gasket seals the freezer/icebox compartment to help maintain proper temperature and reduce frost buildup. It restores the door seal so the appliance runs more efficiently and prevents moisture intrusion. What it does:

• Seals the icebox/freezer compartment to keep cold air in and warm, humid air out
• Helps prevent frost and ice buildup inside the icebox
• Reduces temperature fluctuations that can cause food spoilage
• Can stop condensation or water pooling caused by a failing door seal

• Unplug the appliance before attempting replacement
• Remove the old gasket fully and clean the mounting channel before installing the new seal
• Press the new gasket into the channel evenly; allow time for the gasket to form to the door

The Door Gasket is an OEM part for Whirlpool refrigerators. It creates an essential seal around the refrigerator door, helping to maintain cool interior temperatures and energy efficiency.

Causes of a bad door gasket can include cracks, tears, or compressions from repeated closing of the door over many years of use. Exposure to heat or sharp objects may also damage the sealing material.  

Symptoms of a bad door gasket include: 

• Ineffective sealing allowing warm air into the refrigerator 
• Increased cooling requirement from the compressor to maintain temperatures
• Frost or moisture buildup around the door seal
• Gaps are visible along the door frame where the gasket makes contact

Color: Grey 

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The door gasket is an OEM part for Whirlpool refrigerators. It forms a seal between the refrigerator door and body, working to ensure peak cooling and energy efficiency. This rubber gasket acts as insulation, preventing warm air from entering the refrigerator compartment each time the door is opened.

Causes of a bad door gasket can include cracks, tears, or compression from repeatedly opening and closing the refrigerator door over an extended period of time.

Symptoms of a bad door gasket include:

• Inefficient cooling and higher energy costs
• Warm air leaking into the refrigerator
• Moisture buildup or frost inside the body
• Difficulty properly sealing the door shut

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method

This oven door gasket creates a tight seal between the oven door and cavity to help contain heat for more even cooking and reduce energy loss. It replaces a worn or damaged seal to restore proper door closure and performance. What it does:

• Seals the oven cavity to help maintain correct cooking temperatures and reduce heat leakage.
• Helps prevent smoke and odors from escaping during use.
• Can improve bake and roast consistency when an old gasket is compressed or torn.
• Reduces external door heat, improving safety near the oven face.

• Allow the oven to fully cool and disconnect power before starting work.
• Remove the old gasket and clean the channel or retainer of debris before installing the new gasket.
• Press the gasket into the door retainer evenly around the perimeter; ensure the seal seats fully with no twists.

This refrigerator door gasket seals the perimeter of the door to keep cold air in and warm air out. A fresh, flexible seal helps maintain temperature, reduce frost, and improve energy efficiency and food preservation.

• Creates an airtight seal between the door and cabinet
• Helps prevent temperature swings, frost buildup, and moisture around the door
• Can help with doors not sealing or cooling performance issues related to air leaks

• Unplug the appliance before service; remove food items from the door
• Warm the gasket with a hair dryer on low to relax shipping kinks; do not overheat
• Transfer/seat the gasket fully in the door channel; work evenly around corners
• After installation, close the door and check for uniform contact all around; adjust as needed

This door gasket seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. A direct-fit replacement that restores the magnetic seal for better cooling performance. What it does:

• Re-establishes a tight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and moisture inside the compartment
• Improves cooling efficiency and may reduce excessive run time from a failing seal
• Stops drafts and prevents food spoilage caused by a poor door seal

• One door gasket

• Clean the door frame and remove old gasket before installing the new one
• Warm or flex the gasket as needed for easier positioning; ensure the magnetic seal seats evenly around the perimeter
• Check hinge alignment and door closing after installation to confirm a complete seal
• Follow appliance power-off and safety precautions; refer to the appliance manual for model-specific instructions

This is the rear crisper seal that fits along the back edge of the refrigerator crisper compartment to help maintain the crisper enclosure and reduce air leakage. It restores a tighter seal for better humidity control and food storage. What it does:

• Replaces a worn or torn rear crisper gasket to help reduce cold air loss from the crisper area
• Helps maintain crisper humidity so produce stays fresher longer
• Prevents gaps that can cause uneven cooling or frost build-up near the drawer
• Can reduce draft noise or rubbing caused by a damaged seal

• One rear crisper seal (matches OEM part number)

• Remove the crisper drawer to access the rear seal before replacing
• Peel out the old seal and press the new seal firmly into the gasket channel; ensure an even, continuous fit
• Avoid using sharp tools that could damage the cabinet or new seal
• Unplug the refrigerator or switch off power if needed for safe access to nearby components

This evaporator cover gasket seals the evaporator cover to the refrigerator cabinet, helping maintain proper airflow and reducing frost buildup behind the back wall. It restores a tight seal for more reliable cooling performance. What it does:

• Seals the evaporator cover to prevent air leaks that can cause frost or ice buildup
• Helps maintain consistent cold-air circulation in the freezer/refrigerator compartment
• Reduces chances of excessive frost, water pooling, or longer run cycles tied to air infiltration
• Supports normal defrost operation by keeping warm, moist air out of the evaporator cavity

• Disconnect power before servicing and allow the appliance to defrost if needed
• Remove the evaporator cover carefully; watch for sharp sheet-metal edges and retain fasteners
• Position gasket evenly around the cover mating surface; avoid stretching or creasing the seal
• If adhesive or clips are used, replace or reapply per OEM guidance to ensure a secure fit