Jenn-Air Wall Oven Parts

This oven bottom pan replaces the removable bottom tray that catches spills and protects the oven floor, restoring an even surface for cooking and easier cleanup. Fits in the lower cavity under the oven racks. What it does:

• Provides a durable, porcelain-coated surface to catch drips, crumbs and spills during baking and roasting
• Helps prevent spills from contacting the oven floor and heating elements
• Restores a flat, stable cooking surface for pans and bakeware
• Can reduce time spent scrubbing baked-on messes when used with proper liners

• One oven bottom pan

• Allow the oven to cool completely and disconnect power before replacing the pan
• Remove oven racks, slide out the old pan, then slide the replacement into the same position
• No special tools typically required; handle carefully to avoid chipping the coating

A flexible pan seal that helps keep the refrigerator's drain pan and base area sealed to reduce leaks and contain condensation. Replaces a worn or damaged gasket to help prevent water pooling and odors. What it does:

• Seals the drain/condensate pan to the cabinet base to limit water leaks and vapor escape
• Directs condensate toward the drain so water drains properly instead of pooling
• Helps reduce musty odors from standing water in the pan area
• Commonly replaced when you see water under the appliance, pooling inside the cabinet, or visible gasket damage

• Disconnect power to the appliance before beginning any repair
• Remove the appropriate access panels or kickplate to reach the pan area per your model's service instructions
• Clean the pan and mating surfaces thoroughly before installing the new seal for a proper fit
• Press the seal into place; do not force or use solvents/adhesives unless specified by the OEM

This 20-amp circuit breaker restores overcurrent protection to the appliance's electrical circuit, helping prevent damage from short circuits or overloads. It replaces a worn or tripped breaker so the appliance can receive proper power. What it does:

• Acts as an overcurrent safety device that trips when current exceeds safe limits
• Protects wiring and components from damage caused by overloads or short circuits
• Common symptom: appliance won't power on or stops powering intermittently
• Common symptom: breaker repeatedly trips during normal operation

• Disconnect power at the house breaker before inspecting or replacing the part
• Handle terminals carefully; ensure connectors are fully seated and tight
• Replace with the exact part number for fit and proper electrical rating

This is a replacement thermostat knob that restores safe, easy temperature selection on range and oven controls. The clear indicator and molded grip give reliable adjustment for everyday cooking and baking. What it does:

• Fits onto the thermostat/stove control shaft to set oven or burner temperature
• Replaces cracked, stripped, or missing knobs that are hard to turn or don't stay set
• Provides a visible pointer for accurate temperature selection
• Restores user control when the original knob is worn or damaged

• One black thermostat knob

• Turn power/gas to the appliance off and allow surfaces to cool before installing
• Pull the old knob straight off the control shaft
• Align the knob's splines with the control shaft and push on until fully seated

This replacement grease filter captures cooking grease and large airborne particles to help protect your hood or microwave exhaust system and reduce buildup on internal components. It restores proper airflow and helps maintain cleaner venting. What it does:

• Traps grease and large particulates from cooking vapors to protect internal fan and ductwork
• Helps reduce visible grease buildup and odors on the hood or microwave interior
• Can improve ventilation performance when a clogged or saturated filter is replaced
• Common symptom: heavy grease coating, reduced exhaust effectiveness, or visibly damaged/soiled filter

• Disconnect power to the appliance before servicing or accessing the filter area
• Follow your appliance owner's manual for filter access and removal instructions
• Typically installs by sliding or snapping into the filter slot behind the grille—verify fit before final installation
• If the filter is washable, clean according to manufacturer recommendations; replace if damaged or excessively clogged

This part is a replacement door latch assembly that is intended for use with wall ovens.The door latch assembly makes sure that the oven door locks properly. This is an essential safety component, and the user may notice the appliance doesn't work or certain cycles, such as the self-cleaning cycle, will not start should the latch be faulty. Basic household tools are needed to install this part. Make sure the oven is powered off, unplugged, and cooled down before beginning the repair process.This part is compatible with several different wall oven models that have been manufactured by Whirlpool, Maytag, Kitchenaid, Magic Chef, Amana, Admiral, and some other brands. It is a genuine OEM part from Whirlpool made of high-quality, durable materials. This part is sold individually.

Color: White. Size: 13 oz. Spray paint primer. can.

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

The Gas Range LP Conversion Kit is an OEM part for specific Whirlpool gas ranges. It allows built-in ranges fueled by natural gas to be safely converted for use with liquid propane (LP) fuel. 

Symptoms requiring an LP conversion would include: 

• Inability to ignite or achieve proper combustion using natural gas 
• Unstable burner flame patterns or inconsistent heat output
• Gas leaks or improper connection to an LP fuel supply

Causes for needing an LP conversion kit include choosing to install the range in an area only serviced by LP gas, rather than natural gas. Additional causes could be wear and failure of the original equipment over time.  

This OEM kit is compatible with select Maytag, KitchenAid, Jenn-Air, and Kenmore gas ranges.

This replacement control knob restores a secure grip and accurate selection of settings on your appliance's control shaft. Swap a cracked, stripped, or missing knob to keep everyday operation smooth, precise, and safe.

• Attaches to the control shaft to select temperature, cycle, or burner settings
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like a knob spinning freely, difficulty turning, or inability to choose a setting
• Restores normal feel and alignment when turning the control

• Unplug the appliance and, if applicable, shut off gas before servicing
• Pull the old knob straight off the control shaft; avoid prying on the stem
• Align the new knob with the shaft and press firmly until fully seated
• Test operation to ensure smooth turning and proper engagement

This support is a replacement mounting bracket that secures internal components and restores proper alignment and stability. It helps reduce vibration and prevents loose or sagging parts for safer, quieter operation. What it does:

• Provides a rigid mounting point to hold internal assemblies in place
• Restores correct alignment when panels or components sit unevenly
• Reduces vibration or rattling caused by a broken or missing support
• Helps prevent additional wear on adjoining parts by keeping components stable

• One support mounting bracket

• Recommended for repair by someone comfortable with appliance disassembly
• Disconnect power (and water, if applicable) before starting any repair
• Keep track of mounting hardware and gaskets removed during replacement
• Inspect adjacent parts for wear when installing this support and replace as needed

This small pan seal replaces a worn or damaged sump/pan gasket to help stop leaks and keep water inside the appliance's drain area. It restores a proper seal so the appliance can drain without pooling or seepage. What it does:

• Seals the small pan/sump area to prevent water from leaking onto the floor
• Helps maintain proper drainage and reduces pooling under the appliance
• Restores a tight gasket where cracks, compressions, or wear allow seepage
• Commonly used when you see water under the unit, drips after cycles, or visible gasket damage

• Disconnect power and water supply before servicing the appliance
• Remove access panels and clean the mating surfaces before installing the new seal
• Press the seal into place evenly; ensure it sits flush in the pan/sump channel
• Inspect surrounding parts for damage and replace any brittle or warped components

This grate foot cushions and stabilizes a burner grate on your cooktop. Replacing worn or missing feet helps keep the grate level and protects the surface from scratches, rattling, and metal-on-porcelain contact during cooking.

• Provides a protective cushion between the grate and cooktop surface
• Helps keep cookware level by stabilizing the grate
• Reduces noise and vibration during burner operation
• Replace if feet are missing, flattened, cracked, or the grate rocks

• Turn off power/gas and allow the cooktop and grates to cool completely
• Remove the grate; clean the foot recess and any old adhesive or residue
• Press the new foot firmly into place; if your model uses adhesive, apply a manufacturer-approved high-temperature adhesive and allow it to cure as directed
• Reinstall the grate and verify it sits flat and stable before use

This replacement top burner knob restores smooth, reliable control of your cooktop or range surface burner. Use it to turn the burner on/off and adjust heat when the original knob is cracked, stripped, or missing.

• Mounts on the burner valve or switch stem to control flame/heat level
• Replaces knobs that are broken, loose, or no longer engage the stem
• Helps resolve issues like spinning freely, falling off, or hard-to-set heat
• Restores precise burner control and a clean, finished look

• Allow the appliance to cool; disconnect power and shut off gas before servicing
• Pull the old knob straight off the stem; do not pry on the valve stem
• Align the new knob with the stem and press straight on until fully seated
• The knob markings match the correct burner position before use

Color: Stainless