Kelvinator Panel Parts

The Toeplate is an OEM part for Frigidaire dishwashers, specifically designed to fit seamlessly at the bottom of your appliance. This toeplate not only enhances the aesthetic appeal of your dishwasher by hiding the space beneath the appliance but also serves as a protective barrier, preventing debris from getting under the dishwasher.

Causes of a bad toeplate include physical damage such as dents, cracks, or warping, often resulting from accidental kicks or impacts. Additionally, improper installation can lead to a loose or misaligned toeplate, which may compromise its functionality and appearance.

Symptoms of a bad toeplate include:

• Visible damage or deformation.
• Difficulty in fitting or securing the toeplate to the dishwasher.
• Increased noise or vibration due to lack of insulation or support.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This replacement dishwasher door forms the hinged front of the tub. Replacing a bent or damaged door restores proper alignment and latching so cycles can run correctly and the wash chamber remains properly contained.

• Creates the front barrier of the wash chamber and supports the latch/handle area
• Aligns with the door gasket to promote a proper seal
• Restores correct closing and latching so the cycle can start
• Common symptoms: difficulty closing, cycle won't start due to door not latching, visible dents/warping, poor seal along the gasket

• Disconnect power and turn off the water supply before servicing
• Support the door and carefully relieve hinge spring tension during removal
• Transfer any reusable components from the old door to the new one as needed
• Run a test cycle to ensure proper latching

This outer refrigerator door restores the appliance's exterior and helps maintain proper sealing and temperature control. It replaces a cracked, dented, or damaged door to improve appearance and function. What it does

• Replaces a damaged outer door panel so the fridge can close properly and look like new
• Helps maintain an effective seal when used with an intact gasket, reducing cold air loss
• Stops drafts and visible damage that can lead to higher energy use or interior moisture
• Works with existing hinges and trim when the correct hardware is transferred

• Disconnect power to the appliance before starting and remove food from door shelves as needed
• Transfer existing hinge assemblies, handles, trim, and gasket to the new door unless this part specifically includes them
• Use caution when lifting and aligning the door to avoid chipping paint or damaging the hinge pins
• If you see missing or damaged hardware, get the required screws/hinges separately.

This replacement control console panel restores the front trim that holds the range's controls and display, giving a finished appearance and secure mounting for buttons and the user interface. Fits factory specifications for a direct match. What it does:

• Replaces a cracked, faded, or bent front control panel to restore appearance
• Secures control buttons and display components in the correct position
• Helps eliminate loose or rattling trim around the control area
• Works with existing switches, buttons and electronic modules when they are undamaged

• High-level replacement; remove power to the appliance before starting
• Handle with care to avoid scratching the finish or damaging attached clips
• Retain all screws and fasteners; transfer any brackets or brackets included with the original
• If switches, electronic modules, or wiring are damaged, replace those components instead of reusing them