Kelvinator Guard, Shield, Barrier Parts

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This replacement shield is a molded protective mounting shield that helps protect internal appliance components from debris and physical damage, keeping parts aligned for reliable operation and quieter performance. What it does:

• Covers and protects wiring, harnesses, or small components from contact and debris
• Helps maintain proper alignment of nearby parts to reduce wear and noise
• Prevents incidental interference between moving parts
• Restores intended component protection after damage or removal

• One replacement shield

• Disconnect power before starting any repair to avoid shock or injury
• Handle plastic tabs and mounting points carefully to avoid breaking clips
• Reuse original fasteners if undamaged; replace any broken clips before powering appliance

This shield panel protects internal components and helps direct airflow inside the appliance, replacing a bent, corroded or missing cover to restore proper airflow and reduce contact with moving parts. What it does:

• Covers and protects evaporator and electrical components from debris and accidental contact
• Directs airflow for more consistent temperature inside the compartment
• Stops rattling or interference caused by a loose or damaged shield
• Helps prevent ice buildup and moisture contact when properly seated

• Disconnect power before servicing to avoid shock or injury
• Handle edges carefully — metal panels can be sharp
• Basic hand tools are typically required; follow the appliance service manual for removal and reinstallation
• Secure all fasteners to prevent vibration or contact with moving parts

A replacement interior light shield that protects the refrigerator light and helps diffuse illumination for even lighting throughout the fresh-food compartment. Restores proper light coverage after a cracked or missing lens. What it does:

• Covers and protects the fridge light bulb from spills, debris and accidental contact
• Diffuses light for more even interior illumination
• Prevents direct glare from the bulb to make contents easier to see
• Commonly replaced when cracked, broken, yellowed, or missing

• Remove power to the appliance before starting—unplug or switch off the breaker
• Typically snaps or screws into place; handle gently to avoid cracking the new lens
• Use a soft cloth and mild cleaner; avoid abrasive pads or harsh solvents
• Inspect the housing and replace hardware as needed