Kelvinator Insulation, Sound Dampening Parts

This oven insulation surrounds the oven cavity to retain heat and protect nearby components and cabinetry. Replacing a burnt or deteriorated insulation blanket restores temperature stability and helps keep exterior surfaces cooler on your range during cooking.

• Minimizes heat loss for more consistent baking temperatures
• Shields wiring, controls, and adjacent cabinets from excessive heat
• Damaged insulation can cause long preheat times or trouble maintaining set temperature
• Exterior panels or control area may feel unusually hot, or a burnt odor may persist after spills

• Disconnect power at the breaker; shut off gas
• Allow the appliance to cool completely before service
• Access typically requires pulling the range and removing outer panels; note original routing and retainers for reassembly
• Handle insulation carefully; wear gloves, eye protection, and a dust mask to avoid irritation from fibers

This thermal insulation replaces the heat-retaining blanket used around the oven cabinet. Restoring the insulation helps the appliance maintain temperature and protects surrounding components and cabinetry from excessive heat. What it does:

• Reduces heat loss from the oven cavity to improve temperature stability
• Helps the unit preheat and recover more efficiently
• Limits heat transfer to side panels and the control area
• Reduces persistent burning odors if old insulation was contaminated by spills

• 1 insulation piece

• Disconnect power and allow the appliance to cool completely before service
• If applicable, shut off gas supply before moving a range
• Wear gloves, long sleeves, and eye protection; fiberglass can irritate skin and eyes
• Note factory placement before removal; handle gently to maintain loft, avoid compressing, and ensure no wires are pinched when reassembling

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models. 

This foam cabinet insulation panel helps reduce heat transfer and stabilizes internal temperatures, improving cooling performance and efficiency in the refrigerator cabinet. It replaces torn or missing insulation to help maintain consistent operation. What it does:

• Replaces damaged or missing cabinet foam insulation to reduce temperature fluctuations
• Helps limit frost buildup and uneven cooling caused by gaps in the cabinet
• Supports overall refrigerator efficiency by reducing heat gain from surrounding air
• Covers interior cabinet cavities where insulation is required for proper operation

• One foam cabinet insulation panel

• Disconnect power to the appliance before starting any repair
• Remove shelves and access panels for a clear work area; adhesive or clips may secure the insulation
• Press insulation into place, replacing any fasteners or adhesive strips as needed

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

This foam insulation block helps fill gaps and reduce heat transfer inside the refrigerator cabinet to maintain proper cooling and reduce frost/condensation. It restores the designed insulation barrier where the original piece is damaged or missing. What it does:

• Replaces a damaged or missing foam block that seals internal gaps in the cabinet or behind panels
• Helps prevent warm air infiltration that can cause poor cooling or excess frost
• Reduces condensation and moisture buildup around the evaporator area or panel seams
• Supports consistent temperature performance by restoring insulation continuity

• One foam insulation block

• Disconnect power to the appliance before beginning any repair
• Access location may require removing interior panels or shelves; handle panels and clips carefully
• Install in the exact position and orientation of the original part; use any existing adhesive or fasteners as required
• If adhesive is needed, use only appliance-safe adhesives compatible with foam and follow manufacturer guidance

This cabinet insulation panel helps reduce heat transfer and noise so your refrigerator reaches and keeps proper cooling more efficiently. It's a simple replacement that restores thermal barrier performance inside the cabinet. What it does:

• Replaces worn or damaged insulation to help maintain consistent internal temperatures
• Reduces compressor runtime and thermal cycling caused by heat gain
• Minimizes drafts, cold spots, and excess frost buildup around the cabinet
• Dampens vibration and operating noise for quieter performance

What's included:

• One cabinet insulation panel

Install notes:

• Disconnect power to the appliance before servicing to avoid shock hazards
• Access may require removing interior liners or trim; keep fasteners for reassembly
• Fit the panel into the cabinet cavity in the original orientation; secure as originally installed
• Inspect surrounding seals and components while the cabinet is open; replace any damaged parts

This insulator is a molded protective cushion that reduces vibration and protects nearby components from wear or contact. It helps keep parts stable and minimizes noise for smoother appliance operation. What it does:

• Cushions components to reduce vibration and rattling
• Protects wiring, tubing, and panels from abrasion and impact
• Helps maintain proper spacing between parts to prevent rubbing
• Can reduce operational noise caused by loose or contacting parts

• One insulator

• Disconnect power to the appliance before starting any repair
• Remove the access panel(s) needed to reach the mounting area; retain fasteners
• Press or slide the insulator into the correct position; it fits snugly and secures the component
• If removal requires cutting old adhesive or clips, replace with equivalent fasteners or adhesives approved by the manufacturer