Kelvinator Refrigerator Parts

This condensate drain pan sits at the base of the refrigerator to collect defrost water and allow it to evaporate over the warm compressor, helping prevent floor puddles, moisture damage, and musty odors around the unit.

• Collects and holds defrost condensate from the drain tube (also called a drain pan or drip tray)
• Stages water to evaporate safely using compressor/condenser heat
• Replace if the pan is cracked, warped, missing, or leaking
• Common symptoms: water under/behind the refrigerator, damp flooring, or persistent musty odors near the bottom rear

• Unplug the refrigerator and pull it away from the wall; shut off water supply if connected
• Remove the rear lower access panel to reach the pan near the compressor
• Lift out the old pan; clear any debris from the drain outlet; transfer original mounting hardware if needed
• Seat the new pan level under the drain tube; ensure it's secure and reinstall the access panel

This cabinet breaker kit forms the insulating trim around the appliance opening. It provides a proper surface for the door or lid gasket to seal against and helps minimize condensation along the edge for clean, reliable performance.

• Creates the thermal break and finished edge around the cabinet opening
• Supports correct seating of the door/lid gasket for a consistent seal
• Helps reduce sweating or moisture at the perimeter
• Replaces cracked, warped, or missing breaker trim components

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the door/lid if required for access and retain all fasteners
• Carefully remove old breaker components and clean the mounting surfaces
• Install the new breaker and corners, align evenly, avoid overtightening, and verify the gasket seals all around

This Temperature Controller regulates cooling by switching power to the compressor and related circuits to hold the set temperature. Replacing a failing controller restores accurate temperature control and reliable operation. What it does:

• Cycles cooling components to maintain the temperature you set
• Helps keep cabinet temperatures consistent for proper food storage
• Coordinates on/off operation to prevent overcooling or warm conditions
• Common failure symptoms: too warm or too cold, runs constantly or won't start, control/dial unresponsive

• 1 temperature controller

• Disconnect power before servicing—this is a line-voltage control
• Access the control area, label or photograph wire positions, and move wires one at a time to the new controller
• Reuse existing mounting hardware and any knob/overlay as applicable
• After install, set to mid setting and allow up to 24 hours for temperatures to stabilize

This temperature control knob replaces a worn or broken fridge temperature dial so you can set the refrigerator temperature accurately. It restores a solid grip and clear pointer for reliable, easy adjustments. What it does:

• Fits onto the temperature control shaft to select colder or warmer settings
• Provides a clear pointer for precise temperature selection
• Replaces cracked, stripped, or missing knobs that make adjustments difficult
• Helps eliminate loose or slipping knob operation

• One temperature control knob

• Push-fit installation onto the control shaft; no special tools typically required
• Ensure power is off and remove food before working in the appliance for safety
• Inspect the control shaft for damage; replace the control if the shaft is stripped

The insert nut provides a durable threaded anchor in thin metal or plastic panels. It lets mounting screws tighten securely so covers, brackets, or trim stay fastened and aligned without loosening from vibration.

• Adds internal threads in a thin panel so a machine screw can be used
• Secures panels, brackets, or trim to the appliance cabinet or frame
• Replaces a stripped, damaged, or missing insert to restore screw retention
• Symptoms addressed: screws won't tighten, hardware falls out, panel rattles or shifts

• Disconnect power to the appliance before servicing; shut off water or gas supply if applicable
• Access the mounting location; remove the screw and the old insert if present
• Position the new insert squarely in the hole/slot and press or snap into place as designed
• Reinstall the screw and tighten snugly—do not overtighten to avoid stripping the insert or panel

This electronic control board is the refrigerator's main circuit board that manages temperature, defrost and user controls—restoring responsive control functions and resolving erratic or non-working control behavior. What it does:

• Controls compressor, fans and defrost cycles by sending signals based on sensor inputs
• Manages user interface commands and display response
• Can stop fridge cooling or cause incorrect temperatures when failing
• May cause intermittent operation, no display response, or failure to complete defrost cycles

• Disconnect power to the appliance before starting any work to avoid electrical shock
• Handle the board by its edges and avoid touching components or connector pins
• Verify connector orientation and seating; replace exactly like-for-like to ensure compatibility

This replacement outer cover restores the appliance's exterior appearance and protects underlying components from dirt and damage. It provides a clean finished look where the original cover is cracked, warped, or missing. What it does:

• Covers and protects internal parts behind the trim area
• Restores the appliance's finished appearance after damage or wear
• Helps prevent dirt and debris from reaching internal components
• Matches the original shape for a secure fit and proper alignment

• One outer cover

• Designed to snap or fasten into existing mounting points; reuse original screws or clips unless damaged
• Turn off power to the appliance before attempting removal or installation to avoid injury
• Inspect adjacent trim and fasteners; replace any broken clips to ensure a secure fit

This corner cabinet trim replaces a damaged or missing corner finish piece on the appliance cabinet, restoring a clean edge and helping the door and adjacent panels fit correctly. It provides a cosmetically complete appearance. What it does:

• Covers and protects the cabinet corner for a finished look
• Helps maintain proper alignment and spacing at the cabinet corner
• Commonly replaced when cracked, chipped, broken, or missing
• Restores cosmetic appearance and helps prevent exposed sharp edges

• One corner cabinet trim piece

• Turn off and unplug the appliance before accessing trim or removing panels
• Trim may secure with clips, screws, or snap-fit tabs—inspect fasteners and retainers before removal
• Handle edges carefully; use appropriate tools to avoid scratching adjacent surfaces

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly