Kenmore / Sears Freezer Parts

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

Supports and pivots the freezer lid for smooth opening and proper closing. Replace if hinge is bent, broken, or cracked to restore alignment and seal.

This thermostat is a temperature-sensitive switch that controls power to cooling components as temperatures change. Replacing a worn thermostat restores consistent cycling and more accurate temperature regulation, helping the appliance maintain stable performance. What it does:

• Senses temperature and opens/closes electrical contacts at set points
• Regulates operation of key cooling components to maintain target temperature
• Helps prevent overcooling, overheating, and erratic cycling
• Failure signs include: no cooling, overcooling, temperature swings, unit runs continuously, or short-cycling

• 1 thermostat

• Disconnect power before servicing; verify no voltage is present
• Access the thermostat location; label/photograph wire positions and transfer one at a time
• Install in the same position and orientation as the original to ensure proper thermal response
• Restore power and confirm proper cycling and temperature control

Small mounting bracket that holds shelves or baskets inside your freezer. Replace if cracked, broken, or missing to restore secure, level positioning.

Fridge not cooling or making loud buzzing noise? This compressor kit restores cooling in refrigerators and freezers. Professional repair recommended.

Replacement screw for securing panels, brackets, and internal components in freezers and refrigerators. Use to replace missing or stripped hardware.

Replacement hinge assembly for chest freezer lids. Provides pivot support for smooth opening and secure closing. Replace if cracked, broken, or worn.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Freezer won't shut off or stop cooling? This temperature control thermostat cycles the compressor on and off to maintain set temps. DIY repair.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models. 

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

Mounting bracket that secures freezer shelves and internal panels. Replace if cracked, bent, or broken to restore proper alignment and stability.

Restore accurate cooling and responsive controls with this Electronic Control Board. It monitors sensors and user settings to manage your freezer's key operations so the unit reaches and maintains the temperature you choose.

• Regulates cooling by commanding the compressor and evaporator fan to maintain set temperature
• Interprets thermistor and keypad inputs to execute temperature changes
• Coordinates defrost timing and temperature alarm functions on applicable models
• Symptoms it may address: not cooling or overcooling, runs constantly or won't run, erratic/inaccurate temperature display, beeping alarm, unresponsive buttons or display

• Disconnect power before servicing; handle the board by its edges and use ESD protection
• Note/photograph wiring before removal; transfer any reusable mounting brackets or covers
• Ensure all connectors are fully seated and locked
• After installation, set your desired temperature and allow up to 24 hours for temperatures to stabilize

Almond. Size: 13 oz. can. Acrylic appliance paint.

Replace your burned-out refrigerator light bulb to restore clear visibility inside your appliance. Easy installation when bulb flickers or fails.