Kenmore / Sears Range / Cooktop / Oven Fuse Or Sensor

Range won't heat or shuts off unexpectedly? A faulty thermal fuse may be the cause. This safety component protects against overheating. DIY repair.

Oven overheating or won't heat properly? This safety thermostat monitors backguard temperature to prevent overheating. Simple DIY fix restores safe operation.

This thermal cut-out is a temperature-sensing safety device that helps protect the refrigerator's defrost/heater circuit by opening the circuit when temperatures exceed safe levels. It prevents overheating and helps maintain normal defrost cycles. What it does:

• Senses temperature in the defrost/heater area and opens the circuit to stop heating if temperatures get too high
• Prevents overheating of defrost heater or related components
• Can cause defrost failure symptoms when faulty, such as excessive frost buildup or poor cooling
• May also contribute to long run-times or irregular defrost cycles when not operating correctly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the part and wiring gently; ensure correct orientation and secure connections per service manual
• Use the exact replacement part number for compatibility

This door push-button light switch controls the interior lamp by turning it on when the refrigerator door opens and off when the door closes. It replaces a worn or failed push-button actuator to restore reliable light operation. What it does:

• Completes the circuit to the interior light when the door opens and breaks the circuit when closed
• Commonly causes no interior light, intermittent lighting, or lights that stay on
• Fits in the refrigerator door frame and interfaces with the existing wiring harness
• Simple, single-function electromechanical switch—no electronics to program

• One door push-button light switch

• Disconnect power to the appliance before servicing to avoid shock
• Remove the door trim or bezel as needed to access the switch (requires basic hand tools)
• Handle the switch and wiring gently; do not force connectors or overtighten fasteners

Range won't heat or overheats? This safety thermostat protects against excessive temperatures. Direct replacement part for reliable operation.

Cooktop won't heat or turn on? A blown thermal fuse is often the cause. This safety component protects against overheating. DIY-friendly repair.

Fix inaccurate oven temperatures or error codes with this range temperature sensor probe. Direct replacement part restores precise temp control.

Range won't heat or keeps tripping? This thermal circuit breaker protects your range from electrical overload. Moderate DIY repair in 30-45 minutes.

This thermostat senses appliance temperature and helps the control maintain proper cooling. It replaces a failed temperature switch to restore reliable temperature regulation and protect components from overheating. What it does

• Monitors temperature and signals the control board or compressor to turn cooling on or off
• Prevents overheating by opening the circuit when temperatures exceed safe limits
• Commonly replaced when the appliance does not reach or maintain the correct temperature
• Can stop intermittent cooling or continuous-run symptoms when the original thermostat fails

• One thermostat as shown

• For experienced DIYers only; disconnect power before servicing
• Follow manufacturer instructions and verify correct part placement and wiring before restoring power
• Do not modify the part; use proper tools and replacement hardware

This fixed thermostat monitors and helps regulate appliance temperature to maintain safe operation and reliable cooling/heating. It replaces a worn or failed thermostat to restore proper cycling and temperature control. What it does:

• Opens or closes a circuit at a set temperature to control heating or cooling cycles
• Prevents continuous run by signaling the system to stop when the desired temperature is reached
• Commonly used to address symptoms like no temperature control, compressor or heater running nonstop, or failure to reach set temperature
• Works as a safety/control device to reduce risk of overheating when operating correctly

• One fixed thermostat

• Disconnect power before servicing to avoid shock or injury
• Locate and access the thermostat per your model's service instructions (typically mounted near the evaporator, heater, or air path)
• Handle carefully and avoid bending or damaging terminals; verify function with a multimeter if equipped

Range not reaching correct temperature or displaying inaccurate readings? This temperature probe sensor monitors internal cooking temps. Simple plug-in fix.