Kenmore Washer 110.44832200 (11044832200, 110 44832200) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10135699
The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.
This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.
Do-It-Yourself Stories from Customers like You
Broken spider assembly; aka washer drum shaft assembly Jeff J. • Los Angeles , CA • November 01, 2015
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point...
We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a...
Read more
More
$13.95
- Compare At:
-
$16.60
- You Save:
-
$2.65
Genuine Whirlpool part
By: Whirlpool
Part Number: 280187
The Washer Drain Pump Assembly is an OEM part for Whirlpool washing machines. This assembly is essential for the washer's ability to drain water out of the drum after the wash and rinse cycles, ensuring clothes are properly spun and not left soaking wet.
Causes of a malfunctioning washer drain pump assembly can include blockages from small items or debris, such as coins, socks, or lint, that accidentally make their way into the pump.
Symptoms of a bad Washer Drain Pump Assembly include:
- Water not draining out of the washer, leaving clothes wet
- Unusual noises coming from the pump area, indicating a blockage or damage
- The washer stopping mid-cycle due to inability to drain
- Error codes displayed on the washer related to draining issues
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Saved $$$ doing it myself Bob C. • Sacremento , CA • June 12, 2014
I have a 12 year old Kenmore Elite washer. One day, suddenly, I heard a grinding noise and the washer abruptly stopped. I called a repair service and was told it could be the bearings in the drum of this front-load washer, or it could be the washer's drain pump, which automatically shuts down when the drain pump fails. The repairman said, if it is the drum, it wasn't worth fixing for the age of this washer. It would cost $85 for him to come out and diagnose the problem, then if I decide to fix...
Read more
More
$138.95
- Compare At:
-
$166.74
- You Save:
-
$27.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8182634
The Door Switch Assembly is an OEM part for Whirlpool washing machines. This assembly detects whether the washer door is open or closed, allowing the machine to start or stop the washing cycle accordingly.
Causes of a bad door switch assembly can include wear and tear from frequent use, damage from forceful closing of the door, or electrical issues. A malfunctioning switch can prevent the washer from recognizing a closed door, thus hindering the start of the wash cycle or causing it to stop unexpectedly.
Symptoms of a bad Door Switch Assembly include:
- Washer not starting or stopping mid-cycle
- Error codes indicating door issues
- Washer not spinning or agitating
- Door lock mechanism not engaging or disengaging properly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Won't start
-
Lid or door will not open
-
Lid or door won't close
-
Will not agitate
See more...
Do-It-Yourself Stories from Customers like You
Kenmore front load washer would not start no error code John A. • Woodinville , WA • January 24, 2017
The washing machine would allow you to program it, and all the lights on the control panel would light up, but pressing start did nothing. I tried putting the washer in diagnostic mode, but was unable to do so. The machine was not showing any fault code.
I originally thought it was a problem with the 'Start' button and I thought that I'd buy a replacement part from the original seller of the washer. I was told by the 'live help chat person' that the problem was likely in the washer user...
Read more
More
$81.21
- Compare At:
-
$99.08
- You Save:
-
$17.87
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8181694
The Inlet Valve is an OEM part for Whirlpool washing machines. This valve is critical for controlling the flow of water into the washing machine, ensuring that the right amount of water is supplied for various washing cycles. It consists of solenoids that open and close to allow hot and cold water to enter the wash tub at the appropriate times, according to the selected wash settings.
Symptoms of a failing Inlet Valve include:
- The washing machine not filling with water at the start of a cycle
- Water entering the machine slowly or intermittently
- The machine overfilling or underfilling
- Unusual noises coming from the valve area during the filling stage
- Leakage around the valve
Causes of a bad inlet valve can include mineral deposits from hard water which can clog or block the valve, wear and tear on the solenoids over time leading to failure to open or close properly, and electrical failures that affect the operation of the solenoids.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Hot water slowly dripped into washer tub (1 gallon in a couple of days) Robert M. • Northridge , CA • July 28, 2014
I unplugged the machine. I removed the two fill hoses. I removed the top of the washer case by removing 3 tamper proof screws from the back ( I used my set of "star" head drivers), sliding the top back 1 inch and lifting the top off. I marked the 4 wires with 1 thru 4 stripes with a marker for ID, then pulled the 4 wires off the landing terminals. I removed the mounting screw and lifted the valve up as far as the hose permitted to get a better grip on the valve and hose. I removed the...
Read more
More
$57.22
- Compare At:
-
$67.52
- You Save:
-
$10.30
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10110225
The Water Inlet Flow Meter is an OEM part for Whirlpool washing machines. It is responsible for monitoring and regulating the flow of water entering the washing machine during the fill cycle, ensuring the correct amount of water is added for efficient and effective cleaning.
Causes of a faulty Water Inlet Flow Meter include sediment buildup, physical damage, or electrical issues with the meter's sensors or connections.
Symptoms of a bad Water Inlet Flow Meter include:
- Incorrect water levels in the wash tub
- Washing machine not filling properly with water
- Error codes related to water inlet flow or water level issues
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Unnoticed leak until i removed the top of my front end washer George V. • Homestead , FL • January 03, 2015
This should be plastered all over the place and every owner of a front end washer should be advised or a recall should be issued about this. As I opened the top of my washer to fix a F35 error by replacing the water level switch, which worked out great and it fixed the issue, I noticed a rusting spot at the bottom of the washer just under where the motor is placed. After running the washer with the lid open (I don't recommend doing that) I noticed that it was coming from the top of the soap...
Read more
More
$76.95
- Compare At:
-
$92.34
- You Save:
-
$15.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8182703
The Shock Absorber is an OEM part for Whirlpool washing machines. This component is essential for reducing vibrations and stabilizing the washer drum during operation, particularly during the spin cycle. It helps to absorb shocks and minimize excessive movement, ensuring the washing machine runs smoothly and quietly.
Note: The unit requires a quantity of 4. Package includes 1 only; order as needed.
Symptoms of a failing Shock Absorber include:
- Excessive shaking or vibrating of the washing machine, especially during the spin cycle
- Loud banging or thumping noises during operation
- The washing machine moving or "walking" across the floor
- Visible damage or wear to the shock absorber
Causes of a bad shock absorber can include wear and tear from regular use, heavy or unbalanced loads that put extra strain on the absorbers, or physical damage from impacts or mishandling.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Whirpool duet 10 years old drum would make a rocous during spin cycle Jose F. • Pflugerville , TX • December 06, 2014
Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine).
If you replace the springs, be sure to check for the spring bracket mount. You will also need those.
The washer is running fine. Next I'll work on the dryer.
Read more
More
$43.95
- Compare At:
-
$52.30
- You Save:
-
$8.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10388414
The Drive Belt is an OEM part for Whirlpool front load washing machines. It transmits power from the wash motor to rotate the tub assembly, tumbling clothes during cycles. The belt is designed with deep grooves to securely grip the motor and tub pulleys. It measures 48.22” long uninstalled and will stretch to 51.53” when installed.
Causes of a bad Drive Belt can include cracks developing from repeated flexing during operation or stretching over many years. Debris trapped in the belt path can also wear down the belt prematurely.
Symptoms of a bad belt include:
- The washing tub failing to spin or agitate clothes
- Abnormally loud squealing noises from inside the machine
- The belt slipping off pulleys during cycles
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, and select Kenmore front load washers.
This part fixes the following symptoms
-
Burning smell
-
Will not agitate
-
Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You
Drum not turning Paul H. • Seattle , WA • December 13, 2019
I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive...
Read more
More
$55.95
- Compare At:
-
$66.58
- You Save:
-
$10.63
Genuine Whirlpool part
By: Whirlpool
Part Number: W10902779
The Boot Seal Retaining Ring is an OEM part for Whirlpool washing machines. This ring ensures the boot seal is securely fastened to the washing machine's door assembly. The boot seal retaining ring plays a key role in preventing water leaks by maintaining a tight seal between the door and the drum of the machine.
Over time, the retaining ring can lose its tension, become bent, or suffer from corrosion, leading to a compromised seal.
Symptoms of a bad Boot Seal Retaining Ring include:
- Visible water leakage around the washer door
- Difficulty closing the washer door securely
- A visible gap or misalignment between the boot seal and the door frame
- The boot seal coming loose or falling off
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The bellow tub seal ripped and leaked water all over the laundry room floor James S. • Moscow , TN • September 28, 2014
I used a directional video from AppliancePartsPros specifically made for my specific clothes washer. It made the repair quite simple.
Read more
More
$23.95
- Compare At:
-
$28.50
- You Save:
-
$4.55
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8182210
The Bellow Seal Clamp Ring is an OEM part for Whirlpool washing machines. This ring secures the bellow seal, which is a flexible gasket that provides a watertight seal between the washer door and the drum.
You should replace the bellow seal clamp ring if it becomes damaged or loses its ability to hold the seal tightly. This can occur due to wear and tear, frequent door use, or improper installation. A compromised clamp ring can lead to leaks and inefficient washer operation.
Symptoms of a bad bellow seal clamp ring include:
- Water leaking from the door area during washing
- The bellow seal coming loose or out of place
- Difficulty in keeping the washer door sealed properly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
The bellow tub seal ripped and leaked water all over the laundry room floor James S. • Moscow , TN • September 28, 2014
I used a directional video from AppliancePartsPros specifically made for my specific clothes washer. It made the repair quite simple.
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10467168
The Hose is an OEM part for Whirlpool washing machines. This hose is responsible for carrying water to and from the washing machine during the wash and rinse cycles. It is designed to withstand the pressure and temperature changes associated with the washing process, ensuring a reliable and leak-free connection. IF WASHER HAS AN ECO BALL, THE BALL IS NOT NEEDED AND MUST BE DISCARDED WHEN THE NEW HOSE IS INSTALLED.
Over time, hoses can degrade due to wear and tear, exposure to harsh water conditions, or repeated bending and flexing. Additionally, damage from accidental mishandling or improper installation can also cause hose failure.
Symptoms of a bad hose include:
- Leaks or puddles of water around the washing machine
- Reduced water flow or pressure
- Visible cracks, bulges, or wear on the hose
- Error codes related to water supply issues
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Drain pump and tub to drain pump replacement (error code sud washer not draining) Monty M. • Tooele , UT • August 08, 2016
Repairing the problem was the easy part. Diagnosing the problem took a little more time. To diagnose the problem, it took longer because I first cleaned the Drain Pump trap from all the material it collected. Socks, hair pins, and other materials that were not cleaned from pants pockets. It then still did not drain. Repeated the process after finding more materials and a toy that punctured the hose between the tub and the drain pump. Running the drain and spin cycle takes about 11...
Read more
More
$34.52
- Compare At:
-
$41.08
- You Save:
-
$6.56
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10514214
The Pressure Switch is an OEM part for Whirlpool washing machines. This component is crucial for monitoring and controlling the water level within the washer, ensuring it fills to the appropriate level for each cycle.
Common causes of a bad pressure switch include electrical faults, wear and tear from regular use, or damage due to exposure to water and detergent. These issues can prevent the switch from accurately detecting and regulating water levels.
Symptoms of a bad pressure switch include:
- Washer overfilling or underfilling
- Inconsistent water levels during cycles
- Error codes related to water level issues
- The washer not progressing through cycles properly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
F02 fail to drain repeated suds warnings John C. • Eagle River , AK • February 18, 2019
Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ...
Read more
More
$98.95
- Compare At:
-
$117.75
- You Save:
-
$18.80
Genuine Whirlpool part
By: Whirlpool
Part Number: W10135004
The Suspension Spring Kit is an OEM part for Whirlpool washing machines, designed to maintain balance and stability during the wash cycle. This kit includes 2 springs that work together to support the tub assembly, allowing for smooth operation and reducing vibrations and noise.
Causes of a bad Suspension Spring Kit can include normal wear and tear from repeated use, overload of the washing machine which can stretch or damage the springs, and corrosion due to exposure to water and detergents.
Symptoms of a bad Suspension Spring Kit include:
- Excessive shaking or vibrating of the washing machine, especially during spin cycles
- Unusual noises such as banging or thumping when the tub moves
- The washing machine "walking" or moving from its original position
- Difficulty in keeping the wash load balanced
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Whirpool duet 10 years old drum would make a rocous during spin cycle Jose F. • Pflugerville , TX • December 06, 2014
Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine).
If you replace the springs, be sure to check for the spring bracket mount. You will also need those.
The washer is running fine. Next I'll work on the dryer.
Read more
More
$44.95
- Compare At:
-
$53.49
- You Save:
-
$8.54
Genuine Whirlpool part
By: Whirlpool
Part Number: 285976
Note: This part is a kit of 3 baffles. For 1 baffle, order part# WP8182233. For baffle mounting screw, order part# WPY706189.
The Front Load Washer Drum Baffle Kit is an OEM part for Whirlpool washing machines. This kit includes the drum baffles, which are responsible for lifting and moving clothes within the drum during the wash cycle. This ensures that clothes are thoroughly cleaned by enhancing the tumbling action.
Causes of a bad drum baffle can include wear and tear over time, accidental damage from foreign objects left in the wash, or repeated exposure to heavy loads. These factors can lead to the baffles becoming loose or broken, reducing their effectiveness.
Symptoms of a bad drum baffle include:
- Clothes not tumbling properly
- Excessive noise during the wash cycle
- Visible damage or looseness in the baffles
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Includes 3 baffles. For single baffle only use part number WP8182233. The mounting screw is part number WPY706189.
Do-It-Yourself Stories from Customers like You
Drum baffle broke off James H. • Etna , OH • March 21, 2017
I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would
Read more
More
$64.23
- Compare At:
-
$77.08
- You Save:
-
$12.85
Genuine Whirlpool part
By: Whirlpool
Part Number: 72017
The Appliance Touchup Paint is an OEM product for Whirlpool appliances. This touchup paint is used to cover scratches, chips, and minor blemishes on the surface of various appliances, helping to maintain their appearance and protect them from rust and other damage. It is specifically formulated to match the original color and finish of Whirlpool appliances, ensuring a seamless repair.
Causes of needing touchup paint include everyday wear and tear, accidental impacts that cause chipping or scratching, and exposure to harsh cleaning chemicals that can damage the finish. Regular use of touchup paint can help keep appliances looking new and extend their lifespan.
Symptoms indicating the need for Appliance Touchup Paint include:
- Visible scratches or chips on the appliance surface
- Areas of exposed metal prone to rust
- Blemishes that affect the overall aesthetic of the appliance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Chipped paint Thomas S. • Middletown , DE • September 03, 2014
Touch up paint
Read more
More
$12.55
- Compare At:
-
$15.06
- You Save:
-
$2.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10003250
The Drain Hose is an OEM replacement part for Whirlpool washing machines. Replacements are typically needed due to compression fatigue caused by years of absorbing hydraulic pounding. Additionally, mineral buildup within hoses can reduce drainage efficiency over time.
Symptoms involve:
- Remaining water pockets not fully evacuating after rinses
- Premature alerts about blocked pumps requiring inspection
- Damp loading areas traced to splits along pressure-prone locations
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
F02 fail to drain repeated suds warnings John C. • Eagle River , AK • February 18, 2019
Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ...
Read more
More
$36.62
- Compare At:
-
$43.58
- You Save:
-
$6.96
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10467289
The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal WP8540766. Order separately if needed.
Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.
Symptoms of a bad water temperature sensor include:
- Inability to switch between wash steps or advance through the cycle
- Erratic or inconsistent temperature readings
- Failure alarms or error codes displayed
- Improper or incomplete washing even on high heat settings
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
F2 e3 error code on front load duet washer Mark M. • Saratoga Springs , NY • September 16, 2016
Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since.
Read more
More
$33.46
- Compare At:
-
$39.48
- You Save:
-
$6.02