Kitchenaid Blender Parts

This genuine refrigerator door gasket creates an airtight seal around the fridge door to help maintain proper temperature and energy efficiency. Replacing a worn gasket restores seal integrity and helps prevent moisture and frost buildup. What it does:

• Seals the refrigerator door to keep cold air in and warm, humid air out
• Reduces frost and moisture accumulation inside the compartment
• Helps the compressor run less often by maintaining proper cabinet temperature
• Commonly replaced when you notice air leaks, visible gaps, or a damaged/warped seal

• One door gasket (1 each)

• Inspect the cabinet flange and mounting channel for damage before installing
• Clean contact surfaces and allow gasket to warm/settle for an even fit; follow OEM seating procedure
• Replace with the door closed and check for even contact around the entire perimeter

This replacement bowl cover restores a finished, protective surface around the washer tub opening so clothes and components stay protected and the machine looks right. Fits where the original plastic cover sits around the top of the wash basket. What it does

• Covers the tub opening to help keep clothing and loose items from catching on internal parts
• Helps direct water back into the tub and reduces splash around the rim during a wash
• Protects the top edge of the wash basket and nearby components from wear or impact
• Replaces cracked, warped or cosmetically damaged covers that can snag fabric or look worn

• One bowl cover

• Disconnect power (and water, if required) before starting any repair
• Lift the washer lid and remove any retaining screws or clips securing the existing cover; handle plastic parts carefully to avoid cracking
• Keep small fasteners organized for reassembly; verify alignment before tightening

This O-Ring is a small sealing gasket used in your appliance to create a secure, leak-resistant joint between mating parts. Replacing a worn ring restores proper sealing performance to help prevent drips, seepage, and premature wear. What it does:

• Forms a tight seal between mating components to contain fluids and protect internal parts
• Helps maintain proper system pressure and flow where used
• Reduces leaks at fittings, housings, or shafts
• Typical failure signs: visible seepage, persistent drips, or a flattened/cracked ring

• Includes one O-ring

• Disconnect power and shut off any supply lines before servicing
• Remove the old ring carefully; clean the groove and mating surfaces
• Apply a light silicone-based lubricant to the new ring
• Seat evenly without twisting; reassemble and tighten fittings without overtightening

This interlock collar assembly centers and supports the door/lid interlock so the appliance can detect and secure the door during operation. Restores proper engagement of the latch for reliable start/lock behavior and safety sensing. What it does:

• Positions and stabilizes the interlock/lock mechanism so the door or lid can latch correctly.
• Helps the appliance register a closed/locked door so cycles can start and run.
• A worn, cracked, or broken collar can lead to failure-to-start, door not locking/unlocking, or intermittent door-latch problems.
• Works with the interlock/latch components to maintain safe operation of the door/lid assembly.

• Disconnect power before attempting any service; follow basic electrical safety.
• Replacement requires access to the door/lid latch—use appropriate hand tools and avoid forcing plastic tabs.
• Inspect the interlock and latch components for additional wear; replace damaged parts as needed.
• Refer to OEM instructions for model-specific removal and reassembly guidance.

This replacement disc secures and positions a rotating or drive component inside the appliance, helping maintain proper alignment and reliable operation. It's a simple, durable part used where a small retainer or spacer is required. What it does:

• Holds or centers a shaft, cam or related rotating component to prevent lateral movement
• Helps maintain alignment for smooth rotation and consistent mechanical engagement
• Reduces noise and wear caused by loose or misaligned parts
• Commonly replaced when related components wobble, make noise, or fail to engage properly

• One disc

• Disconnect power (and water if applicable) before beginning any repair
• Inspect surrounding parts (shafts, cams, bushings) for wear and replace if needed
• Install part in the same orientation as the original; do not force or deform the disc

This replacement cap is a small protective cover designed to protect exposed openings and components from dirt, debris and moisture, helping maintain proper appliance performance and reduce wear. What it does:

• Covers and protects exposed shafts, fittings or openings to keep contaminants out
• Helps maintain seals and prevents debris buildup that can cause noise or premature wear
• Restores the part's finished appearance when the original cap is cracked, broken or missing
• Serves as a simple, low-cost repair to avoid secondary damage to adjacent components

• Disconnect power and water supplies before attempting any repair
• Typically presses or snaps into place; inspect mating surface for damage or buildup before installing
• Use appropriate safety gear and avoid forcing the cap onto a damaged part

This replacement jar restores a damaged or missing blender container so you can safely blend ingredients and transfer them without leaks or contamination. It fits the original coupling and seals when seated properly. What it does

• Holds ingredients for blending, mixing, and pureeing.
• Replaces jars that are cracked, chipped, leaking, or otherwise damaged.
• Restores a proper seal with the blender base to prevent leaks during use.
• Lets you resume normal blending performance when the jar is the worn or failed component.

• Ensure the blender is unplugged and the drive coupling is clean before installing the jar.
• Seat the jar fully on the base and the coupling engages smoothly.
• Inspect the jar and any gaskets or seals for damage; replace seals if explicitly required.
• Follow the appliance manufacturer's cleaning and care instructions for this part.

This interlock collar assembly secures the door/ lid interlock hardware so the appliance can detect a closed door and operate safely. It replaces worn or broken collars to restore proper latch engagement and switch alignment. What it does:

• Centers and holds the door interlock/switch assembly in place so the door/lid can fully engage
• Helps the cabinet detect a closed door so cycles can start and run correctly
• Commonly used when the door won't stay closed, the unit won't start, or a door-related fault appears
• Restores proper alignment between the latch and the interlock switch to prevent intermittent contact

• One interlock collar assembly

• Disconnect power (and water for washers) before starting any repair
• May require removal of the top or front panel and the door/lid latch assembly for access
• Handle plastic parts carefully to avoid cracking; verify correct fit before reassembly