Kitchenaid Range / Cooktop / Oven Parts

Fix continuous clicking or no-ignite issues on gas range burners. This spark module controls ignition timing and generates sparks to light surface burners.

Complete burner cap kit for gas cooktops. Sits atop sealed burners to distribute flames evenly. Replace cracked, warped, or discolored caps from heat wear.

The Motor-Fan is an OEM component specifically designed for Whirlpool kitchen ranges. Located within the back wall of the oven cavity, the motor fan works to circulate air and remove excess moisture and smoke during the cooking process. Proper motor-fan functioning helps ensure efficient oven ventilation and performance.

Symptoms of a bad motor fan include:

• Excessive smoke or moisture left in the oven after cooking  
• Oven taking longer to preheat and cook due to poor air circulation
• Loud buzzing or grinding noises emanating from the fan

Causes of failure are normally wear and tear of motor windings or fan blade bearings from years of continuous use. Overheating can potentially reduce lifespan as well. 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement burner grate for gas cooktops. Sits above burners to support cookware. Replace when warped, cracked, rusted, or tie bars are broken or worn.

Fix burners that won't spark or click constantly. This spark module generates high-voltage pulses to ignite surface burners. DIY-friendly, 15-minute repair.

Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

This factory replacement filter helps protect your appliance by trapping unwanted debris and contaminants so the system can perform as designed. Replace a damaged or clogged filter to restore proper flow and dependable operation. What it does

• Screens particles to protect internal components and maintain airflow or water flow
• Helps sustain performance and reduce wear on the appliance
• Common signs it's time to replace: reduced flow/venting, lingering odors, or visible damage
• Preventive replacement can help maintain efficiency over time

• 1 filter

• Disconnect power to the appliance; shut off water supply if applicable
• Access and remove the old filter, noting orientation and seals
• Install the new filter fully seated; do not overtighten any fasteners or fittings
• Restore power (and water, if used) and check for proper operation and leaks/airflow

Fix burners that won't light or produce weak sparks. This gas cooktop igniter restores reliable ignition to surface burners. Quick DIY repair.

Orifice holder mounts beneath the surface burner, securing the orifice spud and directing gas flow. Replace if cracked, damaged, or loose to restore fit.

Burner head for gas range cooktop. Installs beneath cooking surface to distribute flame evenly. Replace if cracked, clogged, or damaged from wear.

Gas range and cooktop surface burner knob. Color: Almond. Measures about 2 inches in diameter. For black order WP3181304. For white order WP3181305.

Fix burners stuck on high or with no heat control. This infinite switch restores precise temperature adjustment. DIY-friendly repair in under an hour.

Black control knob for range burner or oven temperature adjustment. Replaces cracked, broken, or missing knobs. Installs on control panel shaft.

Replace a cracked, stripped, or missing control knob on your electric range. This knob snaps onto the control shaft for accurate cycle and temperature selection.

Controls gas flow and pressure to burners and oven in gas ranges. Replace if leaking, cracked, or damaged to restore safe gas distribution.