Need Help?
Call or text
Replace your range oven door gasket when torn or worn to restore an airtight seal and improve heating efficiency. Easy 5-15 minute install. Confirm fit.
We replaced the Igniters, Spark Module, Door Seal, and Knobs. Read more
Seals your oven door to prevent heat loss and maintain cooking temperatures. Replace if worn, cracked, or heat escapes. Confirm fit with your model.
Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more
Replaces worn dryer front bearing and seal that cause squealing or scraping noise. Essential for smooth drum rotation. Confirm fit with your model.
After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more
Replace your wall oven door cavity gasket when heat escapes or condensation appears. Creates an airtight seal for optimal cooking temperatures. Confirm fit with your model number.
Bought a replacement gasket. Read more
Seals oven door to prevent heat loss and maintain consistent temperature. Replace if frayed, flat, or allowing smoke/heat to escape. Clips install easily.
Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more
Seals the light lens to the oven cavity, blocking heat, steam, and grease from the bulb housing. Replace if cracked, brittle, or missing. Confirm fit.
Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more
Self-adhesive foam seal creates a tight barrier between oven components to prevent air leaks and rattling. Replace when worn or missing to restore quiet operation.
I have a 10 year old Kitchenaid double oven with warming drawer below and electrical connection is located in cabinet below. I order a service manual from http://www.allrepairmanuals.com. If you have the service manual follow it, it walks a technician thru each step. If you don't have a manual here are a few highlights. Disclaimer the following is for my oven model KEBS208DBL8, your oven service steps may vary. IMPORTANT! First step turn-off the power to the oven (mine was a 40 amp breaker)... Read more
Heat-resistant gasket seals oven door to maintain temperature and prevent heat/steam leaks. Replace when worn, cracked, or hardened. Verify fit by model.
Replaced seal. Ordered seal on Monday, had it Tuesday. It was the exact seal for the oven. It took longer to clean up the oven around seal groove than to remove and replace the seal. Read more
Forms a heat-resistant seal between the oven door and cavity. Replace when worn to maintain temperature, reduce heat loss, and ensure even baking.
Whole project took less than 5 minutes. Pull the old gasket out and clip the new gasket back in. Read more
Replace your worn oven door gasket to restore a heat-resistant seal, stabilize temperature, and improve baking performance. Confirm fit with your model number.
Replaced tempered glass and oven seal/gasket. Read more
Prevents heat transfer around oven door glass. Replace if worn, loose, or expanding out of position during heating. Confirm fit with your model number.
Replace your oven door gasket to restore an airtight seal and prevent heat loss. Install when worn or damaged to maintain even cooking temperatures.
Seals the oven door to retain heat and improve temperature accuracy. Replace if torn, brittle, or no longer flexible. Confirm fit with your model.
So, I decided that from the number of screws needed to remove the worn parts and the " plug and play" appearance of the new parts on you website, I decided I could do this! This also how I approach my plumbing projects.....this really scares my husband! Well, everything came in at once so a few days later I decided it was time to do the deed. I had pre-spritzed the existing screws the night before with a degreaser and scrubbed with a used toothbrush. The screws all loosened up with no problem.... Read more
Restores a tight seal between your oven door and cavity to maintain proper temperatures. Replace if you notice heat escaping or uneven cooking. Confirm fit with your model number.
Replace your range door gasket to restore a tight seal and prevent heat loss. Fits worn or cracked seals so your oven door closes properly. Confirm fit.
Seals your microwave door to prevent heat loss and moisture leaks. Replace if cracked, torn, or hardened to restore efficiency. Confirm fit with your model.