Kitchenaid Gasket & Seal

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

Thanks to Jason and his tech people at Appliance Parts Pro, I was able to remove and replace the seal and eliminate all leaks at the bottom of the door. I have a Kitchenaide (Whirlpool) dishwasher model KUDC10IXBL1. Here is how to replace the bottom door seal. 1) Shut off breaker to dishwasher on the electrical panel. 2) Open the dishwasher door completely, and while supporting the door, remove the hex head screws that hold the outside cover. 2) Close the door carefully and slip the outside... Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

• Marks left on clothes

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

• Marks left on clothes

Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

Right-side gasket replacement was straightforward. Left side required removal of mullion, which stumped me. I contacted Appliance Parts Pros who gave me the necessary instructions: Remove the center screw and lift up the mullion. Simple enough, once I knew how to do it. Read more

• Takes too long to dry
• No heat or not enough heat

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

• Leaking

Luckily we planned ahead when building the laundry room, as we built a water catch basin and drain under the washer, but waking up to see 1-2 inches of water is never a good sign - even if it is contained. It appears that a sleeve of a shirt was accidentally caught between the door mechanism and the bellow seal. After a few hundred revolutions in the washer, the shirt knotted up and was torn free of its pinch - in doing so, it tore a quarter sized hole in the rubber bellow seal. This was,... Read more

Door gasket was easy to remove and reinstall. Original gasket was penetrated while cleaning food stuff from folds in the seal below the frig doors. (Gasket is very fragile so don't try to expand the folds while cleaning. I used my finger and a paper towel but in hindsight should have used a Q-Tip. Also, when installing the new gasket you have to be sure the seam folds over the edge of the door and doesn't get caught underneath. Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

The rubber seal/gasket was torn on our KitchenAid refrigerator right side door. I purchased the replacement and followed the directions/recommendations of how to prepare the new gasket for installation. When it's removed from the shipping box, it does have wrinkles and preparing it is a must. I set it out on our tile floor and then used a heat gun (low setting) to warm it up and massage it. It took me about 15 minutes, stopping and restarting as I let the rubber come back to it's desired shape.... Read more

Ordered new gaskets from Appliance Parts Pros, arrived in 4 days. Removed old gaskets and replaced by starting at top corner and. Pushing seal into slot. Day before, opened seal boxes and spread seals to smooth out. Took about 10 minutes to replace both door seals. Right door magnetic seal improved but not great. Adjusted level and installed a 1/16” washer in door bottom hinge, which leveled door better and improved the seal strength. Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more