Lawn Chief Parts

This is a genuine OEM replacement pin commonly found in chippers and shredders. This pin is part of a larger clevis pin and helps secure the larger pin into an engine. Clevis pins are inexpensive metal fasteners that connect parts without having to thread into the body of another part. They have a three-part construction consisting of the clevis, a pin, and a tang. This part is the pin that fasteners the clevis. The most likely reason why this pin would need replacing is if it fell out while the engine was running. Engines produce enough heat to cause parts to expand, and it is possible that a clevis could have expanded and the pin fell out. Should this happen, the clevis will no long fasten, and the pin will need to be replaced. Clevises are found in multiple places throughout an engine, so be sure to follow the user's manual to identify the right part. This pin is compatible with MTD, Huskee, Bolens, and Troy-Bilt clevises and comes sourced from the original manufacturer. This pin does not include a replacement clevis. It ships individually.

This is an authentic OEM replacement .875 coupling for a log splitter. This coupling is used to connect the hydraulic pump shaft and the engine shaft. The engine provides power to the hydraulic pump, which then creates a stream of highly pressurized oil that causes the valve to engage the hydraulic cylinder and split a log. This coupling works in conjunction with a Lovejoy-style rubber spider and .500 coupling. The constant vibrations created by a running engine can wreak havoc on a coupling. Over time, these vibrations can cause the coupling to give out, especially if it is not sized or torqued correctly. Therefore, it is crucial to always check the owner's manual before replacing a part. For safety purposes, be sure to remove the spark plug before disassembling the hydraulic pump. This repair will require a torque driver to tighten the coupling into place. This replacement .875 coupling is a high-quality part sourced directly from its original manufacturer. It is compatible with log splitters made by Huskee, MTD, Troy-Bilt, and Cub Cadet. This part does not include the required .500 coupling or the rubber spider coupling. These parts must be purchased separately.

This is a genuine OEM oil seal sourced directly from the manufacturer for use in the engines of snowblowers and snowthrowers. Oil leaks are prevented using this oil seal on the worm shaft and beside the bearing-flange. It is made from durable plastic that is designed for heavy use; however, over time, the seal can become worn or damaged. Damage or wear to the oil seal can result in oil leaks and loss of engine performance. The oil seal will need to be replaced if oil is leaking from the snowblower. Replacing the oil seal will require a wrench set, pliers, and socket set. Following the diagram for the correct equipment model, disassemble the engine to reach the worm shaft and remove the damaged oil seal. Clean any old lubricant on the area. Install the new oil seal with fresh lubricant. Replace the engine parts in reverse order. Regular lubrication of the worm shaft will add to the engine's performance and prolong the life of the oil seal.This oil seal is sold individually. It is made for snowblowers and snow throwers manufactures by Ryobi, MTD, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, and Husky.

This is an authentic OEM replacement flat washer that has been sourced directly from the manufacturer. It is used with bolts and screws for fastening components on various lawn and garden equipment parts. Flat washers spread the load of the bolt or screw or are used if the hole for the fastener is larger than necessary. The washer fills in the gap, making it more secure. Washers may also be used to prevent the bolt or screw from coming in contact with the component and creating heat or friction that could damage the part. Flat washers are found underneath the head of the bolt or screw, between the fastener and the connected component. Washers may rust or break over time. These changes are visible, and a replacement washer should be installed when necessary.The tools required to remove the bolt or screw depend on what type it is. Wear work gloves when removing and replacing parts. Broken or frayed metal edges can cut. Use the appropriate tool to loosen and remove the fastener. Slide the washer off and place the new one on. Reinstall the bolt or screw and tighten. The flat washer is made of durable metal and sold as an individual component. The flat washer is compatible with chippers, shredders, lawnmowers, tractors, blowers, and other lawn and garden tools manufactured by Craftsman, Bolens, Yard Machines, Troy-Bilt, MTD, Yard-Man, and more.

This part is an adjustable gib that is used on log splitters and chipper shredders. This component is also called a keyway. The adjustable gib locks two shafts together so that they can rotate.A new adjustable gib may be needed if the shaft is freely spinning and will not spin with the drive shaft. If the adjustable gib is cracked, broken, or damaged in any way, it will need to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Never perform care and maintenance on outdoor power equipment that is powered on.This adjustable gib is a genuine MTD part. It is sold individually. This specific adjustable gib is compatible with log splitters and chipper shredders that are manufactured by MTD, Yard Machines, Cub Cadet, Yard-Man, Husky, and Troy-Bilt.

The tri-cut blade works to replace edger blades to ensure they are sharp and capable of cutting through the grass and turf properly. The blade is made from metal and can provide users with clean edging around the edges of their lawn and around flower beds. Regularly examine the edger blade regularly to ensure that it is not bent, broken, or otherwise damaged. If your current edger blade is no longer sharp and cannot be sharpened, it is time for a replacement. Without a sharp blade for the edger, it will be impossible to take care of the lawn properly. To replace the blade in your edger, the only tool required is a wrench. Replacing the blade is easy, and it should not take more than 15 minutes. This OEM part is sold individually, and it works with edgers from a range of brands, including Craftsman, Yard Machines, MTD, Troy-Bilt, Bolens, and Yard-Man.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This hex screw is a genuine MTD part, sold individually. A hex screw can be used as a replacement part for outdoor appliances including lawn mowers, snowblowers, tillers, and wood chippers. This genuine OEM part is a small fastening component.The hex screw in a outdoor appliance might need to be replaced if it has been lost or damaged. If the screw has been damaged and cannot serve its typical function, it should be removed and replaced by this genuine OEM replacement part in a timely fashion.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Husky, Yard Machines, Huskee, Montgomery Wards, Yard Man, and MasterCut.

This carriage bolt is a fastener with a flat tip and a round head with threading along the shank. Also known as coach bolts and plow bolts, the item can be used with many types of lawn and garden equipment. This is a 5/16 carriage bolt that resists turning after the bolt has been tightened. Wear and tear or impact can cause damage to a carriage bolt and lead to the need to replace them.Removing a carriage bolt requires twisting the nut loose from the end of the bolt and then hitting the nut with a hammer. This will begin to move the shoulder out of the lawn equipment. Continue the process until the bolt is loose enough to remove. Installing a new carriage bolt simply requires sliding the bolt into the hole, adding the nut, and tightening things up.This carriage bolt is designed for use with Craftsman, MasterCut, Toro, Yard-Man, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines lawn and garden equipment. It can be used with lawnmowers, chainsaws, snowblowers, edgers, and tillers. This is a genuine OEM product sourced directly from the manufacturer as an individual component.