Lg Dishwasher Dispenser Parts

This door-mounted assembly stores detergent and rinse aid and releases them at the proper time in the wash cycle. Replace a cracked or non-dispensing unit to restore consistent detergent release and overall wash performance. What it does:

• Holds detergent and rinse aid within the inner door
• Releases detergent during the main wash cycle
• Meters rinse aid during the final rinse
• Helps prevent leaks at the dispenser opening
• Common symptoms: detergent left in cup, rinse aid not dispensing, dispenser door won't open, leaks or visible cracks

• One dispenser assembly

• Disconnect power and shut off water supply before servicing
• Remove inner door panel to access and replace the dispenser
• Transfer any reusable seal or hardware from the original part
• After installation, run a short cycle and check for leaks around the dispenser

This small sleeve bushing supports a pivoting or rotating joint in your dishwasher, providing a smooth bearing surface. Replacing a worn bushing helps restore quiet operation and protects mating parts from further wear. What it does

• Provides a low-friction surface between a shaft/pin and bracket
• Helps maintain proper alignment and reduces wobble at the joint
• Can quiet squeaks or grinding caused by wear
• Replacing a cracked or flattened bushing can improve smooth movement

• 1 bushing

• Disconnect power and shut off water before servicing
• Support the door or component attached to the joint to relieve tension
• Note orientation; transfer any spacers/washers in the same order
• Inspect the mating pin/shaft for wear and replace related parts if damaged

This blower cover mounts over the dishwasher's drying fan/vent opening to shield the blower and direct air into the tub. Replacing a damaged or missing cover helps maintain proper airflow and supports consistent drying performance.

• Protects the blower assembly from splashes and debris
• Channels air into the tub during the dry cycle
• Helps maintain the vent seal to limit moisture escape
• Common signs it's needed: poor drying results, rattling near the vent, visible cracks/warping, or moisture around the vent area

• Disconnect power and turn off water supply before servicing
• Access from inside the tub; remove racks if needed
• Note screw locations and any seal orientation; seat the cover evenly and tighten screws snugly without overtightening
• Run a short cycle to check airflow and inspect for leaks

This is the lower cover assembly for your dishwasher. It closes off the bottom of the cabinet to protect internal components and restore a clean, finished appearance. Replace if the panel is cracked, missing, or won't stay secured. What it does:

• Shields the lower chassis from dust, moisture, and impacts
• Helps contain operating noise at the base of the dishwasher
• Restores the front's finished look
• Common symptoms: broken tabs, warped or rattling panel, visible damage, missing cover

• 1 lower cover assembly

• Disconnect power and turn off the water supply before servicing
• Remove the existing lower cover's mounting screws/clips and take off the panel
• Position the new cover; align mounting holes and secure with existing hardware
• Confirm door clearance and recheck level before restoring power

This parts assembly is a direct-replacement assembly used to restore the original mechanical/electrical components it contains so the appliance can operate as designed. It replaces a worn or damaged assembly to help resolve related failures. What it does

• Replaces the factory assembly that houses the appliance's internal components and connections.
• Restores proper component alignment and secure mounting to prevent intermittent faults.
• Addresses symptoms such as failure to operate, unusual noises, loose or damaged internal parts, or intermittent electrical/connectivity issues.
• Works as the factory-specified repair for units showing wear or damage in the affected assembly area.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Handle internal components carefully to avoid damage to wiring, connectors, or sensors.
• Follow the OEM service manual and wiring diagrams for correct installation and routing.

This cover guide is a molded trim piece that helps position and protect the adjacent moving parts for reliable operation and a finished appearance. Replacing a damaged guide restores proper alignment and prevents further wear. What it does:

• Covers and protects the edge of the assembly from debris and impact
• Holds or guides a sliding component to maintain smooth movement
• Prevents rubbing or misalignment that can cause noise or binding
• Common symptom: cracked, broken, loose, or missing cover guide

• One cover guide

• Disconnect power before servicing any appliance components
• Remove only the panels or fasteners indicated by your model's service manual
• Align the guide carefully and secure with the original fasteners; do not force into place

The Dishwasher Inner Pump Housing is an OEM part for LG dishwashers. This component houses the pump, which is essential for circulating water throughout the dishwasher during the wash and rinse cycles.

Causes of a bad inner pump housing can include cracks or damage from debris, mineral buildup from hard water, or general wear and tear over time. Damage to the housing can lead to inefficient water circulation and potential leaks.

Symptoms of a bad inner pump housing include:

• Water leaks under the dishwasher
• Unusual noises during the wash cycle
• Poor cleaning performance
• Reduced water circulation

This OEM LG part is also compatible with Sears/Kenmore.