Lg Dispenser Parts

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

The Detergent Box Assembly is an OEM replacement part for LG washing machines. This assembly is responsible for holding and dispensing detergent and other laundry additives during the wash cycle. It ensures that the correct amounts of detergent, bleach, and fabric softener are released at the appropriate times, contributing to effective cleaning and care of your clothes.

Over time, the detergent box assembly can become worn out or damaged due to continuous exposure to water and detergent. Buildup of detergent residues can clog the compartments, and the mechanical parts of the assembly can also degrade. 

Symptoms of a bad detergent box assembly include:

• The detergent, bleach, or fabric softener not dispensing properly
• Visible cracks, warping, or damage to the box
• Residues remaining in the compartments after a wash cycle
• Leaks from the detergent box area
• Error messages related to dispensing issues

This OEM LG part is also compatible with some Sears/Kenmore washing machine models.

The Dispenser Cover is an OEM part for LG refrigerators. It covers and protects the dispenser area where water and ice are dispensed, ensuring the components remain clean and functional.

Over time, the dispenser cover can become damaged due to repeated use, exposure to moisture, or accidental impact. A compromised cover can affect the appearance of the refrigerator and lead to difficulties in using the dispenser.

Symptoms of a bad Dispenser Cover include:

• Cracks or breaks in the cover
• Difficulty in operating the dispenser
• Water or ice leaking from the dispenser area

This OEM LG part is also compatible with Sears/Kenmore.

Note: This is just the cover and does not include any other components. For the entire assembly, order part number ACQ85430239.

The Ice Chute Door is an OEM part for LG refrigerators. It is located in the ice dispenser area on the front of the refrigerator. It opens and closes automatically when ice is dispensed, ensuring a controlled release of ice cubes or crushed ice into the user's glass or container. The door helps to prevent frost buildup, maintain proper insulation, and protect the ice inside the dispenser.

Causes of a faulty ice chute door can include wear and tear over time, damage due to regular use or accidental impact, or a malfunctioning door motor or solenoid.

Symptoms of a bad ice chute door may include:

• Difficulty in dispensing ice
• Frost or condensation forming around the ice chute area             
• The door not opening or closing smoothly or completely

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Dispenser Assembly is an OEM part for LG front-loading washers. It is responsible for dispensing detergent and fabric softener at the appropriate times during the wash cycle. The dispenser assembly contains separate compartments for detergent and fabric softener, as well as timed mechanisms that release each additive when needed for cleaning and softening results.

Causes of a bad dispenser assembly can include issues with the dispensing mechanisms like clogging, jamming, or malfunctions preventing the timely release of detergent and softener. Damage to compartment seals or lids could also cause improper dispensing.

Symptoms of a bad dispenser assembly include:

• Residue or buildup of detergent in the drum or tub
• Strong detergent or fabric softener odors that won't come out of clothes
• Dispenser drawers, lids, or seals that do not close or lock securely

This OEM LG part is also compatible with Sears/Kenmore.

The Fabric Softener Cap is an OEM replacement part for LG front-loading washing machines. It is a replaceable component that securely fastens into the internal dispenser drawer, containing liquid fabric softener added during wash cycles. Color: blue. It measures about 2-1/2 inches wide by 4-1/2 inches deep.

Symptoms of a problematic cap could include: 

• Softener stains or residue accumulating around base gasket seals  
• Drips or puddles indicative of compromised sealing surfaces
• Cracks, fatigue, or warping affecting secure closure 

Causes typically relate to normal plastic material breakdown after years of opening and closing cycles. Exposure to cleaning detergents could potentially deteriorate gaskets as well.

Compatible brands include Kenmore Elite and some Café laundry appliances too. 

This dispenser assembly is the washer's detergent drawer housing. It channels incoming water through the detergent and fabric softener compartments (and prewash, if equipped) so additives are dispensed at the correct time and helps prevent leaks at the dispenser area.

• Directs water through the dispenser to flush detergent/softener into the tub at the proper points in the cycle
• Replaces cracked, warped, or clogged housings that leak or misdirect water
• Helps resolve detergent or softener remaining in the drawer after a cycle
• Addresses water leaking or overflowing from the dispenser area or visible damage/mineral buildup in the dispenser box

• Unplug the washer and shut off water supplies before servicing
• Pull out the drawer, remove the top cover as needed, then remove mounting screws and release hose clamps to detach the old assembly
• Move hoses/clamps to the new assembly and ensure gaskets/siphon caps are properly seated
• Run a quick fill/rinse to check for leaks before final reassembly

This door-mounted assembly stores detergent and rinse aid and releases them at the proper time in the wash cycle. Replace a cracked or non-dispensing unit to restore consistent detergent release and overall wash performance. What it does:

• Holds detergent and rinse aid within the inner door
• Releases detergent during the main wash cycle
• Meters rinse aid during the final rinse
• Helps prevent leaks at the dispenser opening
• Common symptoms: detergent left in cup, rinse aid not dispensing, dispenser door won't open, leaks or visible cracks

• One dispenser assembly

• Disconnect power and shut off water supply before servicing
• Remove inner door panel to access and replace the dispenser
• Transfer any reusable seal or hardware from the original part
• After installation, run a short cycle and check for leaks around the dispenser

This small cover cap conceals an exposed fastener or opening on your appliance, restoring a clean, finished look. It also helps protect the area from dust and splashes for a tidy, long-lasting installation.

• Covers and protects an open screw hole or attachment point on a panel or door
• Restores a clean, factory appearance
• Helps keep dust and moisture out of the opening
• Common signs it's needed: missing cap, cracked/broken cap, loose cap, won't stay clipped

• Disconnect power (and water, if applicable) before servicing exterior panels or doors
• Note the cap's orientation and any retaining tabs before removal
• Use a plastic pry tool to gently release the old cap; press the new cap until fully seated
• Avoid forcing the cap or overtightening any underlying fastener to prevent damage

This small sleeve bushing supports a pivoting or rotating joint in your dishwasher, providing a smooth bearing surface. Replacing a worn bushing helps restore quiet operation and protects mating parts from further wear. What it does

• Provides a low-friction surface between a shaft/pin and bracket
• Helps maintain proper alignment and reduces wobble at the joint
• Can quiet squeaks or grinding caused by wear
• Replacing a cracked or flattened bushing can improve smooth movement

• 1 bushing

• Disconnect power and shut off water before servicing
• Support the door or component attached to the joint to relieve tension
• Note orientation; transfer any spacers/washers in the same order
• Inspect the mating pin/shaft for wear and replace related parts if damaged

The Detergent Dispenser Box is an OEM part for LG washing machines. Housed within the washer door, this compartment delivers precise amounts of detergent at the optimal time. 

Symptoms of a bad dispenser box include:

• Cracks or breaks compromising the dispenser structure
• Detergent leaking or residual buildup outside of the box
• Failure to fully dispense detergent during wash cycles 

Causes of failure can include plastic fatigue from years of opening/closing the washer door. Repeated impacts may also damage internal mechanisms. This OEM LG part can also be used on Kenmore/Sears appliances. 

This blower cover mounts over the dishwasher's drying fan/vent opening to shield the blower and direct air into the tub. Replacing a damaged or missing cover helps maintain proper airflow and supports consistent drying performance.

• Protects the blower assembly from splashes and debris
• Channels air into the tub during the dry cycle
• Helps maintain the vent seal to limit moisture escape
• Common signs it's needed: poor drying results, rattling near the vent, visible cracks/warping, or moisture around the vent area

• Disconnect power and turn off water supply before servicing
• Access from inside the tub; remove racks if needed
• Note screw locations and any seal orientation; seat the cover evenly and tighten screws snugly without overtightening
• Run a short cycle to check airflow and inspect for leaks

This is the lower cover assembly for your dishwasher. It closes off the bottom of the cabinet to protect internal components and restore a clean, finished appearance. Replace if the panel is cracked, missing, or won't stay secured. What it does:

• Shields the lower chassis from dust, moisture, and impacts
• Helps contain operating noise at the base of the dishwasher
• Restores the front's finished look
• Common symptoms: broken tabs, warped or rattling panel, visible damage, missing cover

• 1 lower cover assembly

• Disconnect power and turn off the water supply before servicing
• Remove the existing lower cover's mounting screws/clips and take off the panel
• Position the new cover; align mounting holes and secure with existing hardware
• Confirm door clearance and recheck level before restoring power

This water tank assembly holds and delivers chilled water to the dispenser and ice system, restoring proper water flow and preventing dispenser dry-running. Direct-fit replacement designed to match the original reservoir's form and function. What it does

• Stores and supplies water for the refrigerator dispenser and ice-making components.
• Replaces cracked or damaged reservoirs that cause leaks or loss of water supply.
• Helps resolve intermittent or no-water dispense when the tank is compromised.
• Works with the refrigerator's fill and drain pathways to maintain correct water levels.

• One water tank assembly

• Disconnect power and shut off the water supply before servicing.
• Drain remaining water from the lines and tank to avoid spills during removal.
• Handle the tank carefully to avoid damaging fittings or mounting tabs.
• After installation, restore water and power, then check connections and test for leaks and proper dispense/ice fill.

This parts assembly is a direct-replacement assembly used to restore the original mechanical/electrical components it contains so the appliance can operate as designed. It replaces a worn or damaged assembly to help resolve related failures. What it does

• Replaces the factory assembly that houses the appliance's internal components and connections.
• Restores proper component alignment and secure mounting to prevent intermittent faults.
• Addresses symptoms such as failure to operate, unusual noises, loose or damaged internal parts, or intermittent electrical/connectivity issues.
• Works as the factory-specified repair for units showing wear or damage in the affected assembly area.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Handle internal components carefully to avoid damage to wiring, connectors, or sensors.
• Follow the OEM service manual and wiring diagrams for correct installation and routing.

The Refrigerator Dispenser Lever is an OEM part for LG refrigerators. It is responsible for controlling and dispensing water from the door-mounted dispenser.

Symptoms of a bad dispenser lever include:

• Difficulty activating or inconsistent water flow when pressed
• Water dispensing without pushing the lever 
• Loose fit or wobbly feel
• Missing or broken lever pieces 

Causes of a bad dispenser lever can be wear and tear over time from frequent use. Exposure to impacts or damage during cleaning can also affect proper function.

This part is also compatible with select Sears/Kenmore models.