Lg Range / Cooktop / Oven Parts

Restore reliable operation with this power control board assembly. It regulates and distributes incoming power to the appliance's circuits and components so the unit powers up consistently and runs as designed when the original board has failed.

• Regulates and stabilizes power delivered to control and load circuits
• Switches power to motors, heaters, fans, and other components via onboard relays
• Provides low-voltage supply for control electronics
• Typical failure symptoms: no power, unresponsive controls, intermittent shutdowns, repeated blown fuse, or visible board damage

• Disconnect power before servicing; capacitors can retain a charge—allow time to discharge and use proper precautions
• Handle the board by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board to maintain orientation
• Inspect wiring, fuses, and downstream components for shorts before restoring power to protect the new board

Color: Stainless

This radiant surface element mounts beneath the glass cooktop to heat a burner zone on your range. Replacing a failed element restores consistent, responsive heating and reliable temperature control for everyday cooking.

• Provides controlled electric heat under the glass for the selected cooking zone
• Works with the range controls to cycle on/off and maintain the set temperature
• Common symptoms: burner won't heat, heats intermittently or only in spots, or the indicator comes on but the surface stays cold
• Visual clues can include a broken or blistered heating coil visible beneath the glass

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift/prop the glass top per service procedure; note wiring and bracket locations before removal
• Transfer any brackets/insulators from the old element and make secure, like-for-like connections
• Handle the glass and element carefully; test operation before final reassembly

This thermostat is a temperature-sensing safety switch that opens the circuit if overheating occurs. Replacing a failed thermostat restores proper protection and helps the appliance run and heat reliably without nuisance shutdowns.

• Monitors temperature at its mounting point and opens the circuit when excess heat is detected
• Helps protect heating components and wiring from heat damage
• Failure may cause no heat, shutdown during use, or operation only after cooling
• Useful when the original thermostat is stuck open or trips repeatedly

• Disconnect power before servicing and allow the appliance to cool completely
• Note wire locations and transfer leads one at a time; ensure snug terminal fits
• Mount firmly and flush to the intended surface for correct thermal contact; do not overtighten
• If servicing a microwave, high-voltage components can be hazardous.

This governor assembly is the mechanical control that stabilizes and regulates motion within the appliance's drive mechanism. Replacing a worn governor restores smooth, consistent operation and helps prevent erratic movement that can strain connected components. What it does:

• Regulates and limits the speed/rotation of the linked drive for stable, predictable movement
• Helps synchronize gears or shafts so the mechanism operates smoothly
• Common symptoms: intermittent or no movement, jerky/erratic motion, clicking or grinding noises
• Visible wear, cracks, or a loose/broken hub on the original governor

• 1 governor assembly

• Disconnect power before servicing; allow moving parts to come to a complete stop
• Note the original orientation; take photos to aid reassembly
• Transfer any reusable brackets, clips, or spacers from the original if required
• After installation, rotate the mechanism by hand to verify free movement before restoring power

This complete parts assembly replaces a damaged or worn internal assembly to restore proper fit and function. Use it to repair an appliance component assembly and help the unit operate as intended. What it does:

• Replaces the original internal assembly that secures or connects related components
• Restores mechanical and/or electrical connections to help correct intermittent operation
• Can address symptoms like a non-functioning subassembly, degraded performance, or unusual noises tied to a damaged assembly
• Matches OEM form and mounting points when the correct part number is used

• One parts assembly

• Disconnect power (and water, if applicable) before beginning any repair
• Use basic hand tools and avoid force when removing clips or fasteners
• Retain all fasteners and orient the new assembly to match the original

Color: White

This factory-specified parts assembly replaces a damaged or missing original assembly in your appliance. Restoring the correct fit and function of the affected components helps the unit operate as designed after wear, damage, or prior service.

• Direct replacement for the assembly identified in your model's parts diagram
• Can help resolve loose or misaligned components, vibration/rattling, or incomplete installation
• Matches original design for consistent fit and performance
• Useful when original pieces are lost or damaged during service

• Disconnect power before service; shut off gas or water if applicable
• Allow the appliance to cool; wear cut-resistant gloves for sharp edges
• Use your model's service manual/parts diagram to take reference photos
• Reassemble panels and test operation after installation

The Burner Cap is an OEM part for LG gas ranges. It sits securely over each sealed burner unit to direct flame upward for focused cooking power.

Causes relate to mineral deposits from years of flame exposure leading to reduced airflow. Damage may occur from rough pot handling as well.

Symptoms of a faulty burner cap can include:

• Yellowing or excessive carbon buildup
• Uneven browning or hotspots on pots and pans
• Flames not fully contained under cookware

This LG part is also compatible with some Kenmore models.
 

This taptite screw fastens panels and internal components in your appliance. It forms its own threads as it's driven to create a secure hold, restoring proper fit and reducing rattles caused by loose or missing fasteners.

• Forms threads in the mating material for a tight, secure fit
• Secures covers, brackets, and assemblies during repair or reassembly
• Replace when the original screw is missing, rusted, stripped, or won't tighten
• Helps address loose or rattling panels and misaligned parts

• Disconnect power before servicing
• Start the screw by hand to avoid cross-threading; use the correct driver
• Do not overtighten; if the receiving hole is damaged, repair or replace the mating component
• Reuse any original washers/spacers in the same order if present

The Switch is an OEM part for LG ovens. This switch is responsible for turning the oven light on and off when the door is opened and closed. It ensures that the oven light operates correctly, providing visibility inside the oven cavity when the door is opened.

A bad oven door light switch can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as the oven light not turning on or off when the door is opened or closed, it may be time to replace the light switch.

Symptoms of a bad switch include:

• Oven light not turning on when the door is opened
• Oven light not turning off when the door is closed

Ensure proper function in your LG oven by replacing the faulty switch with this genuine OEM part.

This LG replacement part is also compatible with select Kenmore models.
 

The Heating Element is an OEM part for LG ranges. It is responsible for providing heat to the oven cavity, allowing for proper cooking and baking. 

The heating element is exposed to high temperatures with each use and over time can become brittle or defective. Causes of a bad heating element can include cracks in the coils, burn marks, or faulty electrical connections. 

Symptoms of a bad heating element include: 

• The oven not heating up or heating unevenly
• Diminished cooking power 
• Burning or burning smell from the oven
• Tripped circuit breaker or blown fuse

Replace yours today with this genuine LG heating element and restore your oven's full cooking capabilities. This OEM LG part is also compatible with Sears/Kenmore.

This power control board assembly manages secondary power distribution for the refrigerator's control systems, restoring reliable operation to displays, sensors, and other subcomponents when a faulty board causes power-related failures. What it does:

• Supplies and routes power to subcomponents like displays, user interfaces, sensors, fans, and ice-maker controls.
• Regulates switching between circuits so electronic modules receive the correct voltage when commanded by the main control.
• Faulty units can produce symptoms such as blank or unresponsive displays, intermittent operation, error codes, or a unit that won't power on.

• Disconnect power to the appliance before beginning any repair.
• Handle the circuit board by its edges and avoid touching connectors; follow ESD (electrostatic discharge) precautions.
• Verify the new board matches the original for connector type and mounting points before installing.

Bake ignitor (glow bar) that draws electrical current and glows to ignite the oven's bake burner. Replacing a weak or failed ignitor restores reliable ignition and consistent oven heating. What it does:

• Heats and glows to open the gas valve and ignite the oven's bake burner.
• Restores normal ignition when a weak or broken ignitor prevents the oven from heating.
• Common symptoms: oven won't heat, long ignition delay, or no glow from the bake burner.
• Direct replacement for the OEM bake ignitor used in compatible gas ovens.

• Disconnect electrical power and turn off the gas supply before servicing the oven.
• Allow the oven to fully cool; handle the glow bar carefully—it's fragile and can be damaged by rough handling or touching the element with bare hands.
• Verify connector type and mounting fit before installing to ensure a correct replacement.

AC synchronous motor assembly that turns the appliance's rotating components to restore normal operation. Replace this motor if the appliance fails to spin, spins intermittently, or produces unusual humming or grinding noises. What it does:

• Replaces the appliance's worn or failed AC synchronous motor to restore rotation and proper function.
• Helps address symptoms such as no rotation, intermittent spinning, humming, grinding, or failure to start.
• Connects to the existing motor mounting and electrical connectors as a direct replacement when the part numbers match.
• Matches OEM function and electrical type (AC synchronous) for compatible appliance platforms.

• Always disconnect the appliance from power before starting any repair.
• Remove the appropriate access panels to reach the motor; support any heavy components (drum/rotator) while you work.
• Verify that the motor's wiring connectors and mounting points match the original before final installation.