Lg Refrigerator Parts

Replacement door stopper assembly that cushions and limits door travel. Installs at the hinge area. Needed when original is cracked, broken, or missing.

Replaces cracked or broken tube connector in your refrigerator. Secures and routes tubing to prevent leaks from loose connections. Easy install.

Replacement air vent shutter knob for refrigerator crisper drawers and shelves. Snaps onto vent lever for fingertip airflow control. Needed when broken or missing.

Ice maker not getting water or refrigerator not filling? This water inlet valve controls water flow to your appliance. Moderate DIY repair in 30-45 minutes.

Replacement cover frame that restores the appearance around the appliance control area while protecting internal components. Use it to replace cracked, warped, or missing trim and keep the control panel edges aligned and secure. What it does:

• Replaces damaged or cracked trim around the control panel for a finished, uniform look
• Protects underlying switches and electronics from dust and light debris
• Helps keep control-panel edges aligned and prevents loose or flopping trim
• Improves overall appliance appearance after impact or wear

• Disconnect power to the appliance before starting any repairs
• Removal of the control panel or console is typically required; keep all fasteners for reassembly
• Handle edges carefully to avoid scratches or cuts and to prevent damage to the new frame

Replacement ice bucket that collects and stores ice in your refrigerator's freezer. Molded plastic bin prevents spills and keeps ice organized.

Protects and diffuses the interior lamp for even lighting. Replace if cracked, yellowed, or broken to restore visibility and shield the bulb from spills.

Fix evaporator coils freezing up every few months with this refrigerator defrost heater assembly. Restores proper defrost cycles in bottom-mount models.

This customized pin is a precision fastener that serves as a pivot or locating point within your appliance. It helps keep mating parts aligned and moving smoothly. Replace a bent, worn, or missing pin to restore proper operation. What it does

• Acts as a pivot/axle or locating pin between connected parts
• Maintains alignment to reduce wobble and uneven movement
• Supports smooth opening/closing or rotation at the joint
• Common signs it's needed: looseness, sagging or misalignment, scraping/squeaking at the pivot, or a visibly worn/bent/missing pin

• One customized pin

• Disconnect power (and shut off water supply, if applicable) before servicing
• Support the door/panel/assembly to remove load from the pin during removal/installation
• Note the orientation and order of any spacers, bushings, or washers and transfer them to the new pin
• Apply a light lubricant and verify smooth movement before restoring power

This is a drip tray that sits beneath the water and ice dispenser on the front of the refrigerator door. It catches overflow, splashes, and drips to prevent water from running down the face of the appliance and onto the floor. Replace this tray if it is cracked, warped, discolored, or no longer fits securely in place.

Supports and guides refrigerator or freezer drawers for smooth sliding. Replace if your drawer slide is cracked, broken, or causing misalignment issues.

Replaces a cracked or broken air duct assembly that routes cold air from the freezer to the refrigerator compartment. Mounts on the back wall of the fridge.

This main PCB power control board assembly replaces the appliance's primary electronic control module to restore power distribution and control functions. It's used when the unit has control or power issues that point to a failed main board. What it does:

• Manages power distribution to the appliance's motors, valves, and sensors
• Interprets control commands and runs electronic cycles for normal operation
• Can cause unresponsive controls, no power, or erratic behavior when faulty
• May trigger control-panel error codes or intermittent starting/stopping

• Disconnect power before servicing to avoid shock; follow all safety procedures
• Handle the board by its edges and use ESD protection to avoid component damage
• Reuse existing mounting hardware and connectors unless otherwise specified by the OEM

Refrigerator won't start or stops running? A failed capacitor disrupts motor circuits. This film radial capacitor restores voltage stability and operation.

Replace your refrigerator's cracked or discolored light lens cover to restore even illumination and protect the bulb from spills and impact. Confirm fit.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.