Lg Refrigerator Drawer, Shelf, Pan

The Freezer Basket Support Rail is an OEM part for LG refrigerators. This component is essential for supporting and guiding the freezer basket, allowing it to slide in and out smoothly. The rail measures approximately 13 x 2 inches.

Symptoms of a failing Freezer Basket Support Rail include:

• Difficulty sliding the freezer basket in and out
• Unusual noises such as grinding or squeaking when moving the basket
• The basket becoming misaligned or tilting when pulled
• Visible wear or damage to the rail

Causes of a bad support rail often include mechanical stress from overloading the basket, frequent use which can wear down the material, or accidental damage during cleaning or rearranging items within the freezer.

This OEM LG part is also compatible with Sears/Kenmore.

This right-side Freezer Basket Support Rail is an OEM part for LG refrigerators. Located inside the freezer compartment, it provides elevated storage shelves for ice cream, frozen vegetables, meats, and more above the freezer floor.

Causes of a bad support rail can include damages such as cracks or breaks that compromise its load-bearing ability over years of use. Sharp freezer temperatures cause constant contraction and expansion.

Symptoms of a bad support rail include:

• Baskets or containers unstable and prone to tipping
• Reduced storage capacity within the freezer
• Safety concerns if a cracked rail were to fully collapse

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Guide Assembly Rail is an OEM part for LG refrigerators. This assembly provides structural support and guidance for the refrigerator drawers, allowing them to slide in and out smoothly. It measures approximately 15 1/2 by 3 inches,.

Causes of a bad guide assembly rail can include wear and tear from regular use, damage from overloading the drawers, or physical impact. A compromised guide assembly rail can lead to difficulty in moving the drawers, affecting the usability of the refrigerator.

Symptoms of a bad guide assembly rail include:

• Drawers not sliding smoothly or getting stuck
• Drawers not aligning properly with the rail
• Unusual noises when opening or closing the drawers
• Visible damage or wear on the rail

This OEM LG part is also compatible with Sears/Kenmore models.

The Drawer Slide Rail is an OEM part for LG refrigerators. This component supports the refrigerator drawers, allowing them to slide in and out smoothly for easy access to stored items.

You should replace the drawer slide rail if it becomes damaged or worn out. Causes of a bad drawer slide rail can include regular wear and tear from frequent use, exposure to heavy loads that strain the rail, or physical damage due to mishandling. A faulty slide rail can lead to difficulty in opening or closing the drawers and may cause the drawers to become misaligned or fall out.

Symptoms of a bad Drawer Slide Rail include:

• Difficulty sliding the drawer in and out
• The drawer not aligning properly with the tracks
• The drawer feeling loose or unstable
• Unusual noises when opening or closing the drawer

This OEM LG part is also compatible with Sears/Kenmore models.

The Guide Rail is an OEM replacement part for LG refrigerator shelves. Running horizontally inside the refrigerator cavity, these durable rails smoothly guide shelf movement during height adjustment. This rail is for the left side.

Causes of faulty guide rails can include dents or damage occurring from heavy loads, as well as plastic degradation from prolonged use. 

Symptoms include:

• Shelves difficult to pull out fully or reinsert  
• Scratching or binding noises heard during adjustments
• Shelves unable to securely lock into place

Note: Per factory, Roller 4580JA3034A and screw 1SBZJA3004K no longer come with guide rail.

This OEM LG replacement is also compatible with select Kenmore refrigerators.

The Crisper Drawer Cover Support is an OEM part for LG refrigerators. This support piece holds the crisper drawer cover in place, providing stability and ensuring that the drawer functions correctly. It helps to maintain the integrity of the crisper drawer structure, allowing for smooth opening and closing while keeping fruits and vegetables fresh.

Over time, the crisper drawer cover support can become damaged due to regular use, heavy loading, or accidental impact. If the support breaks or wears out, it can lead to misalignment or difficulty in operating the crisper drawer.

Symptoms of a bad crisper drawer cover support include:

• The crisper drawer cover not staying in place
•  Difficulty opening or closing the crisper drawer
• The drawer feeling loose or unstable
• Cracks or visible damage to the support piece

This OEM LG part is also compatible with Sears/Kenmore models.

This rail guide assembly is the track a refrigerator drawer or bin slides on. It keeps the drawer aligned for smooth opening and closing and replaces cracked or worn guides that cause sticking, sagging, or binding.

• Supports and guides the drawer along the cabinet wall for stable, level travel
• Restores smooth, consistent opening and closing
• Helps prevent drawers from popping out, tilting, or jamming
• Common symptoms include hard-to-slide drawers, uneven alignment, and visible cracks/broken tabs

• Disconnect power and remove the drawer/bin before starting
• Release locking tabs or screws and note the rail's orientation for reinstallation
• Transfer any clips or mounting hardware from the old guide if needed
• Secure the new guide and test drawer travel for smooth operation

RAIL,SLIDE-RIGHT

This rail guide assembly replaces the worn guide that supports and directs a refrigerator drawer or bin. Installing a new guide restores smooth, level travel and helps prevent sticking, jamming, or misalignment during everyday use.

• Guides the drawer/basket for smooth opening and closing
• Helps keep the drawer level and properly aligned on its track
• Replaces cracked, warped, or broken guide assemblies
• Can address sticking, binding, scraping noises, or a drawer that comes off track

• Disconnect power and remove contents from the affected compartment
• Pull out and remove the drawer/bin; retain screws or clips
• Install the new guide in the same orientation; transfer any reusable hardware from the original part if needed
• The drawer glides smoothly before reloading and restoring power
• Some models use separate left and right guides—match orientation to your model's parts diagram

RAIL,SLIDE-LEFT

This rail guide assembly supports and guides a refrigerator drawer so it slides smoothly and stays aligned. Replace a cracked or worn rail to restore easy opening/closing and keep the drawer from jumping off its track.

• Provides the sliding track and side support for one refrigerator drawer/pan
• Restores smooth movement and proper alignment of the drawer
• Can help resolve sticking, binding, tilting, or the drawer popping off the track
• Often needed when the rail is cracked, stop tab breaks, or wear causes rough travel

• Disconnect power and empty the affected drawer before service
• Remove the drawer (and any shelf above) for clear access; note the original side/orientation
• Release locking tabs or remove mounting screws to swap the rail; secure the new assembly in the same positions
• Reinstall the drawer and test for smooth travel before reloading

This rail guide assembly supports and steers a refrigerator drawer along its track. Replacing a worn or broken guide restores smooth sliding and proper alignment, helping prevent binding and damage to bins and rails.

• Guides the drawer as it opens and closes for smooth movement
• Helps keep the drawer level and properly aligned on the track
• Restores easy operation when the rail is cracked, worn, or deformed
• Typical symptoms: drawer hard to slide, tilts or drops, scraping/grinding noises, visible damage to the rail

• Disconnect power and empty the affected drawer before servicing
• Remove the drawer/bin and any screws or locking tabs securing the old guide
• Transfer any reusable clips or end caps from the old guide to the new assembly if present
• Reinstall, ensure proper engagement on the track, and test for smooth operation

The Crisper Drawer Assembly is an OEM component specifically designed for LG French door refrigerators equipped with bottom-mounted crisper drawers. This assembly provides organized storage for fruits and vegetables.

Causes of a bad crisper drawer assembly can include broken roller glides preventing smooth operation over years of use, cracked or punctured liners allowing air exchange with fridge interior, and damaged humidity control features like crispers.

Symptoms of a bad crisper drawer assembly include:

• Produce drying out faster than expected  
• Difficulty fully closing or opening the drawer
• Drawer unable to be securely held in closed position
• Bowing or warping reducing usable storage space

Replace yours today with this genuine OEM LG assembly to optimize the storage and preservation of perishables. This replacement part is also compatible with Whirlpool, Maytag, and KitchenAid models for factory performance and design.

This connector joins two sections of the refrigerator's water tubing to create a secure, leak-resistant seal. Replace a cracked or loose connector to restore proper water flow to the dispenser and ice maker.

• Provides a sealed union between two water tubes in the appliance's water system
• Helps prevent air and water leaks that can impact dispenser and ice maker performance
• Typical failure signs include drips or puddles near the connection, visible seepage, or moisture alerts
• Also causes low/no dispenser flow or small or hollow ice cubes

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Prepare tubing with a clean, square cut; insert each tube fully into the connector until seated, then pull-test to retention
• Restore water and check all joints for leaks; purge air by dispensing water before normal use

This supporter, holder is the small interior bracket that secures its matching holder/assembly inside your refrigerator. Replace a cracked or missing support to restore a solid, level fit and keep the component from wobbling or dropping.

• Provides structural support for the designated holder/assembly inside the fresh food compartment
• Keeps the component aligned so shelves/covers/bins sit level and operate smoothly
• Direct replacement for a broken, warped, or missing support
• Typical symptoms include: holder won't stay attached, tilting or sagging, rattling when doors close, visible cracks or stripped tabs

• Disconnect power to the refrigerator before servicing
• Remove the item the support holds (such as the related shelf, cover, or bin)
• Release locking tabs and/or remove screws; transfer any reusable hardware
• Align and snap or screw the new support into place, then reinstall the component and verify a secure fit

This slide rail mounts inside the refrigerator and guides a storage drawer so it opens and closes smoothly. Replacing a worn or broken rail restores proper drawer alignment and easy access to stored items. What it does:

• Supports the drawer and provides a smooth glide path along the cabinet wall
• Maintains alignment to keep the drawer level and on track
• Replaces cracked, warped, or worn rails that cause rough, uneven movement
• Common symptoms: drawer binds or sticks, tilts or sags, falls off track, or shows visible rail damage

• 1 slide rail

• Disconnect power to the refrigerator before servicing interior components
• Remove the drawer and any shelf/glass cover to access the rail
• Save and reuse existing mounting screws and any end caps/brackets; match the rail's orientation to the original if your model uses left/right rails
• Align the new rail with factory mounting points, tighten screws, and test for smooth operation