Lg Washer Bracket & Flange

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

This Supporter, Leg is the base bracket that holds the leveling foot at the cabinet. It stabilizes the unit and enables precise leveling to help prevent rocking, vibration, and door or drawer misalignment during everyday use.

• Supports and locates the leveling leg/foot at the base of the cabinet
• Provides a secure mounting point for height adjustment and stability
• Helps keep the cabinet square and reduces wobble and vibration
• Common symptoms of a failed support include rocking, difficulty leveling, or a visibly cracked/bent bracket

• Disconnect power and protect flooring before moving or tilting the appliance
• Access the base area (remove the toe grille/kick panel if equipped)
• Unload the leg, remove mounting fasteners, and transfer the leveling foot to the new support if needed
• Reassemble and verify the unit is level front-to-back and side-to-side

This accessory assembly is the factory-specified kit used to attach or secure designated parts on your appliance. Replacing missing or worn pieces restores a solid, factory fit and finish.

• Provides the original mounting/attachment components specified for your model
• Replaces lost or damaged hardware after installation, moving, or service
• Helps correct loose, misaligned, or rattling parts caused by missing fasteners
• Maintains proper alignment and appearance of exterior parts such as trim or handles

• Disconnect power; also shut off water and/or gas supplies before servicing
• Protect finished surfaces; start fasteners by hand to avoid cross-threading or damage
• Follow your model's service or installation guide for correct order and placement
• After assembly, verify everything is secure and test operation before returning to service

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

This leg support secures the adjustable leveling foot to the appliance's base. Replacing a damaged or stripped support restores a solid mounting point so you can properly level the unit and reduce rocking and vibration. What it does

• Provides the mounting point for the leveling leg; anchors to the base/frame
• Helps keep the appliance level and stable during operation
• Replace if cracked, bent, or the threads are stripped
• Common symptoms: rocking or unstable unit, excessive vibration/rattling, doors out of alignment, leveling foot won't hold adjustment

• 1 leg support

• Disconnect power; shut off water or gas supply if applicable
• With a helper, carefully tip and support the unit to access the base safely
• Remove fasteners, transfer or thread the existing leveling leg into the new support, and reinstall
• Set the appliance down and level it on all corners; verify stability