Parts for Crosley CLCE900FW0: Lower Cabinet / Top Parts

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

The Front Loading Washer Door Lock and Switch Assembly is an OEM part for Frigidaire washing machines. This component ensures that the washer door is securely locked during operation, preventing leaks and interruptions, and also communicates with the control board to allow the wash cycle to start.

Causes of a bad door lock and switch assembly can include wear and tear from regular use, damage from forced door opening, electrical failures within the locking mechanism, or issues with the switch contacts.

Symptoms of a bad door lock and switch assembly include:

• The washer door not locking or unlocking properly
• Error codes related to the door lock
• The washer not starting its cycle
• Interruptions in the wash cycle due to door lock failures

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

The Door Strike is an OEM replacement part for Frigidaire washing machines. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation.

Symptoms of a faulty door strike may include:

• The washer door not closing or latching properly
• Leaks or water seeping out from the door area
• Excessive noise or vibration due to an improperly sealed door

Causes of needing to replace the door strike can include normal wear and tear over time, physical damage or bending of the strike, or issues with the door latch mechanism not aligning correctly.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore washing machine models.

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

This top-front bracket secures the appliance's top or front panel in place to keep panels aligned and stable. Replacing a damaged bracket restores proper panel fit and reduces rattling or loose trim. What it does:

• Mounts and supports the top/front panel to the appliance frame
• Prevents panel movement that can cause noise or misalignment
• Helps maintain correct door or control-panel fit where applicable
• Used when bracket is bent, cracked, or missing mounting holes

• One top-front bracket

• Disconnect power (and water, if applicable) before starting any repair
• Remove necessary trim or panels to access the bracket; retain original fasteners unless new hardware is supplied
• Align bracket and reinstall screws securely; avoid overtightening to prevent strip-out
• If other mounting hardware is damaged, replace it to ensure a secure fit

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This replacement overflow shield directs excess water away from sensitive components to help prevent leaks and water damage in the appliance. It restores proper drainage protection when the original shield is cracked, warped, or missing. What it does:

• Channels overflow or stray water away from critical areas to reduce risk of leaks
• Replaces damaged, cracked, or missing overflow shielding
• Helps maintain proper drainage pathways and component protection
• Commonly used when you see water pooling or dripping near the shielded area

• One overflow shield

• Inspect surrounding seals and fasteners; replace any that are damaged before installing the new shield
• Installation typically requires basic hand tools; secure the shield in the original mounting points
• Disconnect power to the appliance before starting work and restore power only after reassembly

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks

The Drain Hose is an OEM part for Frigidaire washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle.

You should replace the drain hose if it becomes damaged or clogged. Causes of a bad drain hose include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This spacer provides the correct distance and support between components to keep panels, panels and assemblies aligned and stable. It helps reduce vibration and keeps moving parts from rubbing or shifting. What it does:

• Maintains proper gap and alignment between panels or assemblies to ensure smooth operation
• Supports and stabilizes components to reduce vibration and rattling noises
• Prevents metal or plastic parts from contacting each other and wearing prematurely
• Commonly replaced when panels are loose, misaligned, or making noise

• Disconnect power to the appliance before starting any repairs
• Remove only the panels or fasteners necessary to access the damaged spacer
• Install the spacer in the same orientation and location as the original part
• If the replacement requires drilling or modification,

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

One per package.