Parts for Electrolux SFLG4033RT0: 05 - Lower Cabinet / Top Parts

Pan hd phillips ,6-32 x 0.337 ,dog point

The Striker is an OEM component specifically designed for Frigidaire laundry centers. It connects the door to the stainless steel panel, providing secure closure of the unit.

Symptoms of a bad striker include: 

• Loose or misaligned door that does not fit properly
• Latching issue causing the door to open unintentionally  
• Failure points developing around striker mounting location
• Over time increased stresses on other door closure parts

Causes of a bad striker can be normal wear from repeated door openings, damage during moves impacting door alignment, or loose fasteners compromising connections.  

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore laundry center models. Replace promptly before needing other repairs.
 

This strike screw secures the door strike/catch to the appliance, keeping the latch aligned so the door closes firmly and any safety interlock engages. Replacing a missing, stripped, or corroded screw helps restore reliable, consistent door latching. What it does:

• Fastens the strike/catch to the door or cabinet
• Maintains proper alignment for positive latch engagement
• Helps address issues like door not latching, loose/rattling door, or intermittent door switch activation
• Replace if threads are stripped, the head is damaged, or the screw is missing

• 1 strike screw

• Disconnect power before servicing; allow hot surfaces to cool. For gas appliances, also shut off the gas supply.
• Support the door or strike and remove the damaged/missing fastener.
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening.
• Verify door alignment and latch/lock operation after installation.

This electronic control board is the dishwasher's brain, managing cycle logic and communication between the controls and internal sensors. Replacing a failed board can restore responsive controls and consistent, start-to-finish wash performance. What it does:

• Coordinates the dishwasher's operating logic and cycle progression
• Receives inputs from the user interface and door latch and relays commands
• Monitors for faults that trigger beeps or error indications
• Symptoms include no power or no start, unresponsive/intermittent controls, random resets, or stopping mid-cycle

• 1 electronic control board

• Disconnect power at the breaker before service; verify no voltage is present
• Protect the board from static discharge; handle by edges and connector housings
• Document wire/connector positions and transfer them one at a time to the new board
• Access location varies by model (console or base); if your model uses configuration switches/jumpers, match settings to the original per the service sheet

Electronic control that manages the appliance's electronic commands, timers and display functions to restore predictable operation and responsive controls. Replaces a failed control board so cycles and user settings behave as intended. What it does:

• Processes user inputs and runs timed cycles, display readouts, and electronic functions
• Regulates electronic on/off commands and coordinates system sequencing
• Common symptom source for blank or unresponsive control panels, erratic cycles, or incorrect/displayed settings
• Works with the console and wiring harness to relay signals between components

• Always disconnect power to the appliance before servicing to avoid shock
• Photograph or label wiring and connectors before removal to ensure correct reassembly
• Handle the board by its edges and avoid static discharge; do not bend or touch components

This water inlet valve controls the flow of water into the appliance. When energized, it opens to allow water in and closes to stop flow—restoring proper operation when fills are slow, absent, or water seeps when off.

• Regulates water entering the unit during fill or steam-related cycles
• Common fix for no water or very slow fill
• Can resolve water that drips or leaks from the inlet when the unit is off
• May clear "long fill" or "no water" error/fault indications

• Unplug the appliance and shut off the water supply before servicing
• Place a towel or pan to catch residual water when disconnecting hoses
• Mark hose and wire locations to ensure correct reassembly
• After install, open supply valves, check for leaks, and run a test cycle

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

The Fill Hose Assembly is an OEM part for Frigidaire laundry centers. This assembly is responsible for supplying water to the washing machine during the fill cycles. It ensures that water flows smoothly and efficiently from the household water supply to the washing machine, allowing for proper washing and rinsing of clothes.

Causes of a bad fill hose assembly can include wear and tear from regular use, damage from kinks or twists, or deterioration due to mineral buildup. If the fill hose assembly is compromised, it can lead to leaks, insufficient water flow, and potential water damage.

Symptoms of a bad fill hose assembly include:

• Water leaks around the hose connection points
• The washing machine not filling with water properly
• Slow or uneven water flow during the fill cycle
• Visible cracks or damage on the hose

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

Self leveling leg pad

The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.

Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.

Symptoms that may indicate the need for a replacement leveling leg:

• Uneven or unstable washing machine
• Excessive shaking or vibration during spin cycles
• Difficulty in leveling the washer during installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small locating pin used to align and secure parts during assembly, helping panels and components sit correctly for reliable operation. Ideal when a worn or missing pin causes fit or alignment issues. What it does:

• Positions and holds panels, trim, or assemblies in the correct location during reassembly
• Prevents shifting or misalignment of covers and access panels
• Restores proper fit where a bent, broken or missing pin causes loose trim or gaps
• Small, simple replacement that addresses common fit/fitment symptoms

• Disconnect power and unplug the appliance before beginning any work
• Use basic hand tools; avoid forcing parts into place to prevent damage
• Inspect surrounding components for damage and replace if worn

This is a replacement 12-24 UNC machine screw used to secure appliance panels and internal components so fittings stay tight and stable during use. It restores proper fastening where the original screw is damaged or missing. What it does:

• Fastens and secures panels, brackets, and component assemblies
• Helps stop rattling, loose parts, or gaps caused by a missing or stripped screw
• Provides correct thread engagement for 12-24 UNC threaded holes
• Replaces worn, rusted, or damaged screws to restore original fit

• Disconnect power and water to the appliance before servicing
• Use the correct driver and size to avoid stripping the head
• Thread in by hand first, then tighten snugly—do not overtighten
• Replace only with the exact part number to ensure proper fit and function

This door lock assembly secures the washer door and signals the control that it's safe to run. Replace it to restore reliable locking and allow cycles to start and spin as designed. What it does:

• Locks and releases the door at the correct points in the cycle
• Sends door-closed status to the main control board
• Prevents the door from opening while the tub is moving
• Common symptoms: cycle won't start, "door open/locked" message, door won't lock or unlock, washer won't spin

• Door lock assembly

• Disconnect power before servicing; internal components can move unexpectedly
• Access the lock behind the front panel/door gasket area; remove the door-boot clamp and mounting screws as needed
• Transfer wiring connectors one at a time to the new lock to maintain correct orientation
• Test door operation and run a quick cycle check before final reassembly

This is a replacement dispenser assembly for your refrigerator's door dispenser. It restores the external dispenser trim/assembly so you can use the ice and water dispensing area reliably and keep the door looking finished. What it does:

• Replaces a cracked, broken or damaged dispenser housing or trim piece
• Restores proper alignment and user interface for dispensing water or ice
• Helps stop drafts or moisture intrusion around the dispenser opening
• Can resolve cosmetic damage or functional issues where the dispenser lever/area is compromised

• Disconnect power and shut off the water supply before beginning work
• Remove the inner door panel as required to access and remove the old dispenser; keep fasteners for reuse unless damaged
• Handle the dispenser and door trim carefully to avoid scratching or cracking during installation
• After installation, restore power and water supply and check for proper operation and any leaks

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This control panel bezel is the exterior trim piece that surrounds and protects your appliance's control area, restoring a finished look and helping keep controls free from grease and debris. Ideal for cosmetic repairs and panel protection. What it does:

• Replaces damaged, scratched, or discolored control panel trim to restore appearance
• Shields control buttons and displays from spills, grime, and everyday wear
• Helps maintain proper alignment of control components and finish
• Can improve usability by providing a clean, unobstructed control surface

• Disconnect power to the appliance before starting any work to avoid electrical shock
• Handle trim carefully to avoid scratching; use a soft cloth and protect work surface
• Removal/installation typically involves releasing clips or removing a few screws—retain fasteners for reassembly