Parts for Electrolux SFLG4033RT0: 03 - Motor / Blower / Belt Parts

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

This replacement housing is the body that holds the washer's detergent drawer and channels rinse water through each compartment into the tub. Replacing a cracked or warped housing restores proper dispensing and helps prevent leaks at the dispenser area.

• Supports and aligns the detergent/bleach/softener drawer
• Routes incoming water to flush each compartment into the wash tub
• Interfaces with inlet hoses and outlet chute for proper flow
• Common symptoms: water leaking from the dispenser/front panel, detergent or softener left in the drawer, poor dispensing, drawer difficult to open/close

• Disconnect power and shut off water supply before servicing
• Remove necessary panels/trim, pull out the drawer, and release mounting screws/clips to access the housing
• Label and disconnect hoses; note routing. Transfer any reusable siphon caps, seals, and the drawer from the original housing
• Reassemble, restore water and power, and run a test fill to check for leaks

The Blower Wheel is an OEM part for Frigidaire clothes dryers. This component works to propel hot air through clothes during drying cycles.

Causes of a bad blower wheel involve wear from years of operation, such as bearing deterioration or plastic fan blade cracking/warping. Foreign object damage or improper cleaning techniques pose other risk factors.

Symptoms of a bad blower wheel include:

• Slow or weak drying even on high heat settings
• Loud clanking or grinding noises from inside the duct
• The dryer not activating or functioning when turned on
• Reduced air discharge observable at the vent

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Control Thermistor is an OEM part for Frigidaire dryers. This component plays a critical role in regulating the temperature inside the dryer by monitoring the internal conditions and sending temperature data to the control board. The control board then uses this information to adjust the heat cycle, ensuring clothes dry evenly and safely. 

Symptoms of a failing control thermistor include:

• Clothes not drying properly or cycles running too hot or too cold
• Frequent stopping or starting of the dryer
• Error messages related to temperature or sensor issues displayed on the control panel

Causes of control thermistor failure generally involve faulty wiring, accumulation of lint and debris affecting the sensor's accuracy, or wear and tear from regular use that leads to degradation of the sensor components.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

The Idler Arm Assembly is an OEM part for Frigidaire dryers. It is an essential component of the dryer's drum support system, responsible for maintaining the proper alignment and smooth rotation of the drum during operation. The idler arm assembly typically consists of an idler arm, pulley, and bearings, working together to support the weight of the drum and facilitate its rotational movement.

Symptoms of a bad idler arm assembly in a dryer include:

• Loud squeaking or grinding noises during operation
• Excessive vibration or shaking of the dryer
• Difficulty in starting or maintaining the drum's rotation
• Potential damage to other components due to misalignment

Causes of a bad idler arm assembly can include wear and tear over time, damage from foreign objects entering the drum, or issues with the bearings or pulley components. A faulty idler arm assembly can lead to improper drum alignment, increased friction, and potential damage to other parts of the dryer.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drum Belt is an OEM part for Frigidaire dryers. It plays a pivotal role in the mechanism of the dryer, connecting the motor to the drum to enable its rotation. Without a functioning belt, the dryer's drum will not turn, preventing clothes from drying properly.

Symptoms of a failing Drum Belt include:

• A dryer that turns on but does not spin
• Unusual noises, such as thumping or squealing, coming from the dryer
• Clothes taking longer than usual to dry
• The dryer stopping unexpectedly during a cycle

Common causes for Drum Belt issues are general wear and tear from regular use, the belt becoming stretched or misaligned, and excessive load sizes that strain the belt beyond its capacity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement power cord restores the electrical connection for compatible Frigidaire appliances so they can safely receive power. Durable insulation and molded ends help ensure a secure, reliable feed to the appliance. What it does

• Provides the main AC power connection between the appliance and the household outlet.
• Replaces damaged, frayed, or burned cords that can cause power loss or unsafe conditions.
• Common symptom: appliance does not power on or loses power intermittently.
• Common symptom: visible cord damage, exposed wires, melting, or frequent tripping of a circuit breaker.

• Always disconnect the appliance from power at the breaker or unplug before installing.
• Inspect the cord routing and strain relief; replace any damaged clamps or covers.
• Tighten terminal connections securely; avoid over-torquing which can damage terminals.

Hex washer head ,10-32 x 0.375. Ground

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This mounting bracket secures and supports appliance panels and internal components, restoring proper alignment and stable operation. It's a simple replacement that helps eliminate loose panels and rattling. What it does

• Provides a secure anchor point to hold panels, rails, or assemblies in place
• Restores correct alignment to doors or access panels when a bracket is broken or bent
• Reduces vibration and rattling caused by a loose or missing support
• Matches OEM fit and function for straightforward replacement

• One mounting bracket

• Disconnect power and, if applicable, water before starting any repair
• Inspect surrounding parts and fasteners; replace any damaged screws or clips
• Use appropriate tools and fasteners for a secure installation; avoid overtightening
• Handle sharp edges carefully and test panel alignment after installation

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

The Ignitor is an OEM part for Frigidaire dryers. This part ignites the gas burner that generates the heat necessary for drying clothes.  Note: Part has been redesigned and is now a flat style ignitor instead of round ignitor.

Causes of a bad Ignitor can include wear and tear from regular use, electrical issues such as short circuits or power surges, and physical damage from debris or residue buildup.

Symptoms of a bad Ignitor include:

• The dryer not heating up, leading to clothes remaining wet after a cycle
• The ignitor not glowing or sparking when the dryer is turned on
• Extended drying times due to insufficient heat production
• The smell of gas without ignition, indicating a failure to light the burner

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a replacement mounting collar used to secure and align associated appliance components for proper fit and operation. It restores the original spacing and support where the factory collar is worn or damaged. What it does:

• Provides a secure mounting point to hold panels, assemblies, or shafts in correct alignment
• Helps prevent excess movement that can cause noise, vibration, or premature wear
• Restores proper spacing to prevent rubbing or binding of adjacent parts
• Useful when a cracked, deformed, or missing collar causes misalignment or rattling

• Always disconnect power to the appliance before beginning repairs to avoid shock or injury
• Inspect surrounding parts and mounting hardware; replace any damaged fasteners for a secure fit
• Hand-start fasteners to avoid cross-threading, then tighten to OEM torque if specified

The Dryer Heat Sensor is an OEM part for Frigidaire dryers. This sensor monitors the temperature inside the dryer drum to ensure clothes are dried effectively and safely by regulating the heat levels during the drying cycle.

Causes of a bad heat sensor can include wear and tear from frequent use, buildup of lint or debris, or electrical issues. A malfunctioning sensor can result in incorrect temperature readings, leading to under-drying or overheating of clothes.

Symptoms of a bad Dryer Heat Sensor include:

• Clothes not drying properly or taking too long to dry
• Dryer overheating or shutting off unexpectedly
• Inconsistent drying cycles
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This cable tie secures wiring and small hoses to appliance frames and harnesses, keeping components organized and reducing wear from rubbing or vibration. It helps maintain safe routing so wires stay clear of moving or hot parts. What it does:

• Fastens wire bundles, harnesses, and small hoses to prevent movement
• Keeps wiring routed away from sharp edges and heat sources
• Reduces noise and wear caused by loose or vibrating wires
• Helps prevent chafing that can lead to insulation damage or intermittent connections

• Disconnect power before servicing electrical components
• Position ties to secure harnesses without over-tightening; trim excess tail
• Keep ties away from high-heat surfaces and moving parts
• Replace any damaged or brittle ties rather than reusing