Parts for Ge PB960FJ5DS: Lower Door Parts

This oven door insulation pad fits behind the inner door liner to help retain heat in the oven cavity and reduce heat transfer to the outer door. It restores proper oven temperature control and improves cooking consistency. What it does:

• Replaces worn or damaged insulation that can allow heat to escape from the oven cavity
• Helps the oven reach and maintain set temperatures for more even baking and roasting
• Reduces excessive outer door temperatures and hot spots on the range front
• Restores the intended thermal barrier between the oven cavity and outer door assembly

• One oven door insulation pad

• Disconnect power to the appliance before starting any repair; allow the oven to cool completely
• Installation commonly requires removing the oven door and inner door liner—follow OEM instructions
• Handle insulation carefully; wear gloves and a dust mask if material is fibrous

This oven door insulation side panel fits inside the oven door to help reduce heat transfer and improve cooking consistency. It replaces damaged or missing insulation to help maintain proper oven temperatures and protect the door assembly. What it does

• Helps retain heat inside the oven for more even cooking and efficient operation
• Reduces exterior door temperature by insulating the inner door cavity
• Prevents hot spots and heat loss caused by torn, compressed, or missing insulation
• Supports the oven door structure and helps keep inner components protected

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the oven door per the manufacturer instructions to access internal insulation
• Handle insulation and door components carefully; wear gloves and eye protection
• Follow OEM instructions for reassembly and proper placement of the insulation panel

The Oven Door Gasket is an OEM part for GE ranges. This gasket is responsible for creating an air-tight seal between the door and the oven housing. It allows heat to be properly contained within the oven cavity during the cooking process. 

Causes of a bad gasket can include warping, cracking, or breakdown of the gasket material over repeated heating and cooling cycles. Exposure to excessive heat or impact damage is also possible. 

Symptoms of a bad gasket include:

• Inability to maintain proper oven temperatures 
• Leaks of heat, smoke, or flames from the door seal area
• Drafts or cold spots felt around the door perimeter
• Difficulty in fully latching the oven door closed

This OEM GE replacement gasket is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven door insulation retainer secures the insulation inside the oven door, helping maintain proper heat containment and preventing insulation from shifting. It's a small but important clip that keeps the door's inner components stable. What it does:

• Holds inner door insulation in place so insulation stays positioned during use
• Helps maintain consistent heat distribution by preventing insulation gaps
• Reduces rattling or movement of the door interior when opening or closing
• Commonly replaced when insulation is loose, visible, or shifting inside the door

• One oven door insulation retainer

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Access typically requires removing the oven door or inner door panel — follow your model's service instructions
• Handle door panels and insulation carefully to avoid damage; keep fasteners organized for reassembly

This replacement door-handle bracket secures the refrigerator door handle to the door, restoring a firm, aligned grip. Durable black finish matches the original part and helps keep the handle properly positioned during everyday use. What it does:

• Secures the door handle to the refrigerator door so the handle stays tight and aligned
• Replaces cracked, broken or worn brackets that cause a loose or wobbly handle
• Restores proper handle engagement for opening and closing the door
• Helps prevent additional stress to the handle and mounting area

• One black door-handle bracket

• Basic hand tools required; for exact steps
• Support the handle during removal and installation to avoid dropping or damaging the door
• Disconnect power and water before working on the appliance for safety
• If screws or fasteners appear stripped or damaged, replace them to ensure a secure fit

This left door hinge secures and pivots a refrigerator or freezer door so it opens and closes smoothly. Replacing a worn hinge restores proper door alignment and helps the seal close evenly to maintain temperature. What it does:

• Provides the pivot point that supports the door and allows smooth opening/closing
• Restores correct door alignment to help prevent sagging or uneven gaps
• Reduces binding or scraping that can occur with worn or bent hinges
• Helps the door seal fully to reduce cool-air loss and compressor overwork

• Unplug the appliance and empty/secure the door before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use the existing screws or included hardware as specified by the OEM; tighten fasteners securely

The Window Pack Assembly is an OEM replacement part for GE electric ranges. It comprises the outer oven window and securing brackets that hold the glass in place.

Causes of failure can include cracks in the glass from impact or thermal stress over time. Mounting brackets may loosen from normal use.

Symptoms of a faulty window pack assembly include:

• Fogging or condensation between panes of glass
• Leaks evident around the perimeter of the oven window
• Window that rocks or wiggles in the frame
• Inability to securely latch the window shut

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore oven models.

Replacement screw that secures panels, trim and internal brackets to keep appliance components stable and rattle-free. Use when originals are missing, stripped, or broken to restore proper fit and safe operation. What it does:

• Secures panels, control housings, trim and small brackets so parts stay aligned and stable.
• Replaces missing or damaged fasteners that cause rattling, vibration, or loose assemblies.
• Keeps electrical and mechanical components properly positioned for reliable operation.
• Intended as a direct replacement where the OEM screw specified for the application is required.

• Disconnect power and unplug the appliance before starting any repair.
• Use the correct screwdriver or bit and seat the screw squarely to avoid stripping the head or threads.
• Do not overtighten—stop when snug to prevent damage to panels or plastic components.
• Keep removed screws organized; replace only with the identical OEM screw for proper fit.

ST10-16 X 7/16"

Package of 12

This 10-32 machine screw secures brackets, panels, and other hardware in cooking appliances. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned and safely fastened. What it does:

• Fastens panels, brackets, and components using a 10-32 machine thread
• Replaces hardware that is missing, rusted, or stripped
• Helps address loose or rattling parts and minor panel misalignment
• Maintains secure mounting after service or part replacement

• One 10-32 machine screw

• Disconnect power; for gas appliances, also shut off gas before service
• Support the panel or bracket while removing/installing hardware
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace them one at a time to keep alignment

This is a replacement screw used to secure panels and components on compatible appliances. It provides a direct-fit fastening solution to restore proper part alignment and prevent rattling or loose panels. What it does

• Fastens appliance panels, brackets or assemblies where an 8-18 x 5/8 screw is specified
• Replaces missing or stripped fasteners that allow parts to shift or vibrate
• Restores secure mounting for components to reduce noise and movement
• Useful when a factory screw is damaged, corroded, or lost during service

• One screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver size and type to avoid stripping the head
• Install by hand first, then snug with a driver—do not over-torque
• Keep removed hardware organized to ensure correct reassembly