Parts for Frigidaire GRQC2255BF0: Lower System Parts

This electronic control is the main circuit board that manages the appliance's functions and user commands, restoring proper cycle selection and timed operations when the original board fails or behaves erratically. What it does:

• Manages cycle timing, sensors and user inputs so the appliance runs selected programs
• Communicates status to displays and indicator lights for normal operation
• Replaces a board that causes unresponsive controls, erratic cycle behavior, or failure to start
• Works with existing wiring harness and front-panel controls to restore factory functions

• Disconnect power before beginning work to avoid shock; follow safety guidelines for the appliance type
• Handle the board by the edges and avoid static discharge; use ESD protection if available
• Note connector locations and mounting hardware during removal for correct reassembly

This is a replacement mounting screw used to secure appliance panels and small components so parts stay firmly in place during normal use. Installing the correct screw restores proper fit and reduces rattles or loose trim. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Keeps components aligned to prevent vibration and noise
• Replaces a lost or stripped screw to restore secure attachment
• Helps maintain safe, stable operation by holding parts where they belong

• One replacement mounting screw

• Disconnect power and water before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can damage threads or panels
• Keep removed fasteners organized so you reinstall them in the original locations

This clamp secures flexible hoses and lines to prevent leaks and maintain proper flow. It's a simple replacement part that restores a tight, reliable connection on compatible appliances. What it does:

• Holds a hose or tube firmly to a fitting or barb to stop leaks and disconnections
• Helps maintain proper water, air, or drain flow by preventing slippage
• Commonly replaced when a hose slips, vibrates loose, or shows corrosion at the clamp area
• Works wherever a band-style hose clamp is specified by the manufacturer

• Disconnect power and shut off water before starting any repair
• Loosen the old clamp and slide it off the hose, then position and tighten the replacement clamp evenly
• Use the correct screwdriver or nut driver to avoid stripping the clamp screw
• After installation, restore power/water and check the connection for leaks while the appliance runs

This condenser assembly is the refrigerator heat-exchange coil and support frame that helps remove heat from the refrigerant so the appliance can maintain proper cooling. Replaces a worn or damaged condenser to restore normal cooling performance. What it does:

• Transfers heat from the refrigerant to the surrounding air so the compressor and refrigeration cycle can work efficiently
• Restores normal cooling when the condenser is bent, corroded, or leaking
• Helps prevent compressor overheating when functioning correctly

• One condenser assembly (coil and mounting frame)

• Disconnect power to the appliance before starting any repair
• Take care handling fins and tubing; edges can be sharp and coils can be punctured
• Verify fit and mounting locations against your model's parts diagram before installation

This fan motor-and-blade assembly restores airflow in compatible Frigidaire refrigerators and freezers to help maintain even temperatures and reduce warm spots. It replaces a failed fan to improve circulation and appliance performance. What it does:

• Circulates air inside the fresh food and freezer compartments for more even cooling.
• Moves air across cooling components to help prevent localized frost and warm zones.
• Replaces noisy, stalled, or non-spinning fans that cause reduced cooling or unusual sounds.
• Supports proper airflow so the appliance can maintain set temperatures more consistently.

• Disconnect power before starting—unplug the appliance or shut off the circuit breaker.
• Access typically requires removing interior panels or the rear evaporator cover; retain fasteners.
• Handle blades carefully to avoid bending; ensure electrical connectors are fully seated.

This condenser shroud is the molded cover that protects the refrigerator condenser coil and helps direct airflow for efficient cooling performance. It replaces damaged or missing shrouds to restore proper condenser protection and airflow routing. What it does

• Covers and protects the condenser coil from debris and accidental contact
• Helps channel airflow across the condenser for efficient heat dissipation
• Prevents objects from obstructing the condenser fins, which can reduce cooling
• Fits into the lower rear cabinet area to maintain proper component positioning

• One condenser shroud

• Remove power to the appliance before accessing the condenser area
• Handle carefully to avoid bending or damaging condenser fins and mounting tabs
• Typical installation uses existing screws or clips; confirm all fasteners are present and secure

This shaft is a direct-replacement support pin that restores proper alignment and rotation in compatible Frigidaire appliances. It helps return worn or damaged supports to factory fit so components turn smoothly. What it does

• Supports and aligns a rotating component so it turns true and without excessive wobble
• Transfers rotational force from the motor/drive to the drum or rotor
• Common symptom: loud noise or scraping during operation
• Common symptom: drum or component feels loose or wobbly when spun by hand

• Disconnect power before starting any repair.
• Access may require removing panels or the appliance drum; keep track of fasteners.
• Inspect mating bearings, bushings, and seals; replace if worn to prevent premature wear of the new shaft.

This replacement roller is a small support wheel that helps appliance doors or drawers move smoothly and stay aligned. It restores quiet, steady operation and reduces sticking or uneven travel when worn rollers cause binding. What it does

• Replaces a worn support wheel to restore smooth sliding or rolling motion
• Helps maintain proper door/drawer alignment and prevents scraping
• Reduces noise and sticking caused by cracked or flattened rollers
• Supports weight transfer so moving parts operate evenly

• One replacement roller

• Power off and unplug the appliance before starting any repair
• Access may require removing a kick plate, drawer, or door—keep fasteners organized
• Inspect adjacent tracks or mounts and replace any damaged clips or screws

The Thermostat Kit is an OEM part for Frigidaire refrigerators. It regulates interior temperature conditions. The thermostat monitors and controls cooling functions to maintain even temperatures for food storage.  

Causes of a bad thermostat can include a gradual loss of calibration or component failure over many cooling cycles. Temperature swings, increased energy use, and icing/freezing issues may result. Exposure to moisture or humidity could also compromise insulation and wiring.

Symptoms of a faulty thermostat include:  

• Inconsistent or fluctuating interior temperatures
• Difficulty maintaining the temperature setting  
• Frost or ice buildup inside the fridge or freezer
• The compressor running constantly without adequate cooling

This OEM replacement is compatible with Electrolux, Gibson, Kelvinator, and Kenmore brands as well.