Parts for Frigidaire GRQC2255BF0: Shelves Parts

This replacement cover restores the appliance's exterior appearance and helps protect internal components from dust and debris. It fits over the designated cabinet area for a finished, safe look. What it does:

• Protects internal parts from dust, moisture, and accidental contact
• Restores a clean, finished exterior where the original cover is dented, cracked, or missing
• Helps keep wiring and components concealed and secured
• Prevents small objects from entering service areas

• Disconnect power (and water, if applicable) before starting any repair
• Remove any adjacent trim or retaining fasteners to access the cover
• Use appropriate hand tools and avoid over-tightening fasteners

This water reservoir tank holds and supplies cold water to the refrigerator's dispenser/ice system so the appliance can make ice and deliver water on demand. Replaces a cracked or leaking reservoir to stop drips and water loss. What it does

• Collects and stores water routed from the inlet valve for the dispenser and ice maker.
• Maintains ready water supply so the dispenser and ice maker can operate normally.
• Commonly replaced when the tank is cracked, leaking, or causing low/no water delivery.
• Can prevent water damage and restore reliable dispensing when the original tank fails.

• One replacement water reservoir tank.

• Disconnect power and shut off the water supply before starting; drain remaining water from the lines.
• Handle carefully to avoid stressing inlet/outlet fittings and gaskets; replace any worn seals.
• Verify hose/clamp connections are secure and test for leaks after restoring power and water.

This replacement rail is the sliding track that supports and guides a refrigerator drawer for smooth opening and closing. Restores proper alignment and helps prevent sticking, binding or drawers coming off the track. What it does:

• Provides a stable track for a refrigerator or freezer drawer to slide in and out smoothly
• Keeps the drawer aligned to prevent scraping or binding against the cabinet
• Helps stop drawers from falling forward or detaching when pulled
• Replaces worn or damaged rails that cause rough or uneven drawer movement

• Disconnect power and remove contents before working on refrigerator drawers
• Often accessed by removing the drawer and/or inner liner; basic hand tools may be required
• Reinstall drawer and test operation; ensure rail is seated and aligned before use

This complete drawer assembly replaces a broken or worn refrigerator drawer so you can store and access frozen or chilled items without rubbing or gaps. It restores smooth sliding and proper sealing for reliable cold storage. What it does:

• Replaces damaged, cracked, or warped drawers that block proper closure or storage
• Restores smooth sliding action so the drawer opens and closes easily
• Helps maintain proper airflow and temperature by providing a correct fit
• Reduces rattling, catching, and items falling out when the drawer is pulled

• Designed for direct replacement; match part number before ordering
• Remove power or secure refrigerator per manufacturer guidance before service
• Handle plastic components carefully to avoid cracking during installation
• If rails or mounts are damaged, inspect and replace those parts separately

This mounting bracket secures a refrigerator component to restore proper alignment and reduce movement. It provides a simple, reliable replacement to stop rattling or sagging where a worn or broken bracket is the cause. What it does

• Provides a fixed mounting point to hold panels or internal components securely in place.
• Restores proper alignment to parts that have become loose, preventing rubbing or mis-seating.
• Helps eliminate noises caused by a loose or broken support.
• Suitable when the original bracket is cracked, bent, or missing.

• Disconnect power to the appliance before starting any repair to avoid electrical or mechanical hazards.
• Basic hand tools are typically required; use appropriate fasteners as originally supplied.
• Keep small parts and fasteners secure during removal/installation.

This is a replacement mounting screw used to secure appliance panels and small components so parts stay firmly in place during normal use. Installing the correct screw restores proper fit and reduces rattles or loose trim. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Keeps components aligned to prevent vibration and noise
• Replaces a lost or stripped screw to restore secure attachment
• Helps maintain safe, stable operation by holding parts where they belong

• One replacement mounting screw

• Disconnect power and water before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can damage threads or panels
• Keep removed fasteners organized so you reinstall them in the original locations

This is a replacement refrigerator door gasket that helps restore a tight seal to the door, improving temperature control and reducing frost buildup and energy loss. What it does:

• Seals the refrigerator door edge to keep cold air in and warm, moist air out
• Helps prevent frost buildup and excessive compressor runtime
• Can resolve symptoms like warm interior temps, visible gaps when door is closed, or moisture/ice along the door seal
• Restores proper door closing and magnetic seal engagement when undamaged

• Disconnect power or unplug the appliance before servicing to avoid electrical hazard
• Remove the old gasket completely, clean the gasket channel, and press the new gasket into the channel evenly
• Verify the gasket is fully seated around the door and check for uniform contact when the door is closed
• Follow the manufacturer's instructions carefully

This drawer assembly replaces a broken or cracked refrigerator storage bin so you can safely store and organize food. It restores proper sliding and containment for everyday fridge use. What it does:

• Holds and organizes refrigerated items while keeping them contained
• Slides in and out on cabinet tracks for easy access
• Replaces drawers that are cracked, warped, or no longer seating properly
• Helps prevent spills and keeps produce separated from other shelf items

• Disconnect power to the appliance before beginning any repair
• Remove shelves or items from the cabinet, slide out the old drawer, and lift to release from tracks
• Align new drawer with cabinet tracks and lower into place until it seats; check for smooth operation
• Do not force parts; if resistance occurs, recheck alignment

This cover is an access panel that protects internal oven/range components and keeps wiring and controls out of sight. It restores a clean finished appearance and helps prevent dust and debris from entering sensitive areas. What it does

• Shields control housing and internal components from spills, dust, and accidental contact
• Helps keep wiring and electrical connections covered and tidy
• Replaces cracked, broken or missing trim that exposes underlying parts
• Restores proper fit and finish to the appliance exterior

• Disconnect power to the appliance before attempting any service to avoid shock.
• May require basic tools (screwdriver) to remove fasteners and secure the replacement.
• Handle carefully to avoid scratching the finish; verify fasteners and alignment before tightening.

This guide helps the refrigerator/freezer drawer open and close smoothly while keeping the drawer aligned. It restores proper drawer movement and reduces rubbing, sticking, or uneven travel for a more reliable storage experience. What it does:

• Guides the drawer along its track to ensure smooth, straight travel
• Prevents drawer from binding, catching, or coming off the track
• Maintains proper drawer alignment and load support during operation
• Reduces noise and wear caused by misaligned or damaged guides

• Disconnect power before servicing to avoid electrical hazards where applicable
• Remove the drawer completely to access the guide; installation generally requires basic hand tools
• Inspect mating track and hardware; replace any worn screws or clips for secure fit

This manifold routes and distributes supply within the appliance to the connected components. Replacing a cracked or leaking manifold restores proper flow and helps maintain safe, reliable operation across the system.

• Channels supply from the inlet to multiple connection points
• Provides threaded ports for model-specific fittings and connections
• Helps maintain consistent flow to downstream components
• Typical failure signs: leaks, visible cracks, stripped threads, or multiple components not receiving supply

• Disconnect power and shut off the appliance's supply before servicing.
• Access and replace the manifold per your model's service instructions; transfer any brackets or fittings from the original as required.
• Use manufacturer-approved sealants only where specified; do not overtighten threaded joints.
• Restore supply and check every connection for leaks before returning the appliance to service.

The Frigidaire PureSource Ultra II Refrigerator Water & Ice Filter is an OEM part for Frigidaire refrigerators provides clean, fresh-tasting water and ice. This advanced filtration system is specifically engineered to remove impurities and contaminants from your water supply, including lead, chlorine, mercury, and certain pesticides, without removing beneficial fluoride. 

Regular replacement of the water and ice filter is crucial for maintaining the quality of your drinking water and the efficiency of your refrigerator's water and ice dispensing system. Over time, filters can become saturated with contaminants, reducing their effectiveness and potentially impacting the taste and safety of your water.

Symptoms of a filter in need of replacement include:

• Reduced water flow from the dispenser
• Unpleasant taste or odor in the water and ice
• The refrigerator's water filter indicator light turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This inlet water valve controls water flow to the refrigerator's dispenser and ice maker, restoring proper water delivery when the appliance won't fill or dispense. Designed as a direct replacement for the factory valve. What it does:

• Opens and closes the water supply to the ice maker and door dispenser when signaled by the refrigerator controls
• Restores water flow when a faulty valve causes no water or intermittent dispensing
• Helps stop leaks by sealing off water when the valve fails closed or is stuck open
• Works with the refrigerator's solenoid/valve circuit to regulate water pressure to components

• One inlet water valve

• Disconnect power and shut off the household water supply before starting
• Replace only with the matching valve; ensure inlet/outlet lines and electrical connectors match
• Use basic hand tools; avoid over-tightening fittings to prevent damage

This replacement tubing routes water between components inside your appliance. It restores reliable, leak-resistant water flow when the original line becomes brittle, kinked, or damaged, helping dispensers and ice systems work properly on applicable models.

• Transports water between the inlet valve and internal components
• Replaces tubing that is cracked, brittle, kinked, or leaking
• Helps address issues like leaks, reduced dispenser flow, or ice maker fill problems on applicable units
• Maintains proper water flow and pressure within the line

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water and relieve line pressure
• Note the original routing; transfer any retainers or clips from the old line; ensure connections are fully seated and ends are cut square if trimming is required
• Restore water and power, then check all connections carefully for leaks

This replacement door gasket seals the refrigerator fresh-food compartment to help maintain consistent temperatures and keep food fresh. It restores the cabinet seal to reduce airflow and prevent moisture buildup around the door. What it does:

• Forms an airtight seal between the fresh-food door and cabinet to help maintain interior temperature
• Helps reduce frost build-up and prevents warm air from entering the compartment
• Can stop drafts or uneven cooling caused by a torn, warped, or compressed gasket
• Fits where a continuous magnetic refrigerator door seal is required

• One door gasket

• Inspect the door frame and mounting channel for debris before installing; clean area for a proper seal
• Gasket typically stretches and inserts into a retainer channel; warm with a hair dryer if needed for easier fitting
• Check for full compression around the perimeter and trim excess material only if specified by the OEM
• Disconnect power or follow appliance safety guidance when working near electrical components or light switches

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling