Parts for Ge UNC15NJBII: Machine Compartment Parts

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This condenser fan motor circulates air across the condenser to help your refrigerator reject heat and run efficiently. Replacing a failing motor restores proper airflow and can reduce compressor overuse. What it does:

• Spins the condenser fan blades to move air over condenser coils and dissipate heat
• Helps maintain proper cooling performance by supporting condenser and compressor operation
• Commonly fails with symptoms such as a noisy or non-spinning fan, refrigerator running warm, or frequent compressor cycling
• Designed to replace the factory condenser fan motor used in compatible GE refrigerators

• Always unplug the appliance before starting any repair
• Basic hand tools may be required; keep small parts and fasteners organized

Replacement condenser fan blade that circulates air across the condenser to help dissipate heat and keep your refrigerator running efficiently. Installs on the condenser fan motor to restore proper airflow and cooling performance. What it does:

• Pushes air through the condenser coil so the refrigerator can reject heat effectively
• Restores balanced airflow when a cracked, warped, or missing blade causes poor cooling
• Eliminates rubbing or scraping noises caused by damaged or bent blades
• Helps prevent the compressor from running excessively due to reduced condenser cooling

• Disconnect power to the appliance before beginning any service.
• Verify the blade is seated squarely on the motor shaft and secured with the original retainer.
• Check blade clearance so it does not contact the shroud or housing when the motor turns.
• If mounting hardware or the motor coupling is damaged, replace those parts as needed.

This drain hose routes and removes excess water from the appliance to the household drain, helping prevent pooling and water damage. It's a direct-fit replacement designed to restore proper drainage when the original hose is damaged or clogged. What it does:

• Directs discharge water from the appliance to the drain connection
• Restores normal drainage when a cracked, split or clogged hose causes leaks
• Helps prevent water pooling under or inside the appliance
• Reduces risk of water-related damage when installed and secured correctly

• Disconnect power and turn off water supply before starting.
• Remove the old hose, route the replacement following the original path, and secure with existing clamps or fasteners.
• Check all connections for tightness and test by running a short drain cycle to confirm no leaks.

This small clamp hose secures and seals low-pressure appliance tubing to prevent leaks and keep lines routed properly. Use it to replace a worn or damaged hose clamp and restore a reliable connection. What it does:

• Fastens small-diameter tubing to fittings to help stop water or air leaks
• Keeps hoses routed and seated to prevent kinks or disconnection
• Replaces brittle, cracked, or loose clamp sections that cause drips or poor flow
• Works on low-pressure lines typically found in refrigerators and ice/water systems

• Disconnect power and water supply before beginning any repair
• Verify correct location and orientation before removing the old clamp
• Use pliers as needed to compress or position the clamp; avoid over-tightening

This elbow drain hose redirects wastewater through a curved drain connection to help remove water from the appliance and stop leaks caused by damaged or kinked tubing. Simple replacement when the original hose is cracked or leaking. What it does:

• Channels drain water through a curved elbow to the drain line or pump
• Restores proper drainage when the original hose is split, cracked, or leaking
• Helps prevent kinks at the connection point for more reliable flow
• Common symptom fix for water pooling under or behind the appliance

• Disconnect power to the appliance and shut off the water supply before beginning.
• Remove the damaged hose and replace with the new elbow hose, ensuring a snug fit on both fittings.
• Secure with the correct clamps; there are no twists or sharp bends that could restrict flow.
• Test for leaks after restoring power and water.

Replacement pressure switch that senses pressure changes and signals the control board to manage water fill, airflow or cycle events. Restores proper sensing so the appliance fills, dispenses or cycles as intended. What it does:

• Detects air or water pressure changes and sends an electrical signal to the control board.
• Stops overfilling or underfilling by monitoring water-level/flow pressure.
• Helps control cycling functions tied to pressure-based safety or timing.
• Common symptom: appliance fails to fill, overfills, or the cycle doesn't advance.

• Disconnect power (and water supply if applicable) before starting work.
• Match the replacement to the original by checking connectors and mounting orientation.
• Handle the switch and terminals carefully; avoid bending contacts or pinching tubing.