Parts for Ge ZIR360NNBRH: Machine Compartment Parts

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Fix a refrigerator that won't power on with a new 3-prong grounded power cord. Restores electrical connection when the original cord is damaged or broken.

Guides airflow across the condenser and secures the fan motor in place. Replace if cracked, broken, or missing to restore proper cooling airflow.

Fix a refrigerator that's not cooling or has an overheated compressor. This condenser fan motor circulates air over the compressor and coils. DIY-friendly.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Rear condenser fan mounting bracket for refrigerators and freezers. Replaces broken, cracked, or missing brackets that secure the fan assembly.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Hex washer head screw for refrigerators, freezers, and other appliances. Replaces lost, stripped, or damaged screws during repairs or panel assembly.

Refrigerator not cooling? Compressor won't start? This inverter board controls compressor speed and cooling. Moderate DIY repair with electrical testing.

Fix a refrigerator that won't cool, has display errors, or runs constantly with this main control board assembly. Manages compressor and defrost cycles.

Insulating spacer that mounts between the control circuit board and chassis in freezers. Replace if cracked, broken, or missing to maintain proper board spacing.

This 8-32 x 5/8" Phillips screw is a stainless steel fastener used to secure panels and components in appliances. It resists corrosion and provides a reliable, low-profile Phillips head fastening solution. What it does:

• Fastens panels, brackets and trim where an 8-32 x 5/8" screw is specified
• Stainless steel construction helps resist rust in humid or food-prep environments
• Phillips head accepts standard drivers for quick, positive installation
• Replaces worn or stripped fasteners that cause loose or rattling parts

• One 8-32 x 5/8" Phillips stainless steel screw

• Unplug the appliance or disconnect power before beginning work
• Use a properly sized Phillips screwdriver to avoid cam-out or stripping
• Tighten until snug; avoid over-tightening which can strip threads or crack plastics

Refrigerator not cooling or running constantly? A damaged condenser coil prevents proper heat release. This assembly restores cooling efficiency.

Condenser air baffle for refrigerators. Directs airflow over the condenser coils. Replace if cracked, broken, or missing to maintain proper air circulation.

Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.

This process dryer tube is the replacement tubing used in the dryer's process/airflow assembly to channel heated air. It helps restore proper airflow routing for drying performance and prevents leaks or air loss. What it does:

• Channels heated air from the blower/heating assembly through the dryer's process path
• Restores proper airflow routing to improve drying consistency
• Helps reduce air leaks that can lower drying efficiency or cause uneven drying
• Used when existing tube is cracked, damaged, or deteriorated

• One process dryer tube

• Disconnect power before servicing to avoid electrical shock
• Inspect surrounding ducts, clamps, and seals and replace if worn
• Use proper clamps or clips to secure tube and ensure airtight connections

This discharge tube routes water from the refrigerator supply to the dispenser or ice-making components, restoring proper water flow and preventing leaks. It's a direct-fit replacement when the original tube is cracked or blocked. What it does:

• Channels water from the supply line to the dispenser or ice maker assembly.
• Restores normal dispensing and ice-filling when a cracked or clogged tube causes reduced flow.
• Prevents leaks or drips caused by split or brittle tubing.
• Maintains proper routing to avoid kinks that restrict water delivery.

• Disconnect power and shut off the water supply before starting any repair.
• Access may require removing interior panels or the refrigerator rear access panel; keep fasteners organized.
• Replace damaged tubing only; inspect nearby fittings and clamps and tighten or replace if needed.

Mounting screw for refrigerators and freezers. Secures internal components and panels. Replace if stripped, missing, or damaged during maintenance.