Parts for Ge ZSAS420DYASS: Machine Compartment Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Secures and elevates the main control board to prevent electrical shorts. Replace if broken, cracked, or missing to restore proper board clearance.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Drip pan and vaporizer assembly that collects defrost water beneath your refrigerator. Replace if cracked, rusted, or missing to prevent leaks.

Fix a refrigerator that's not cooling or has an overheated compressor. This condenser fan motor circulates air over the compressor and coils. DIY-friendly.

Rear condenser fan mounting bracket for refrigerators and freezers. Replaces broken, cracked, or missing brackets that secure the fan assembly.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

Rubber grommet that mounts the evaporator or condenser fan motor to its bracket. Replace when worn, cracked, or missing to reduce vibration and noise.

Refrigerator not cooling or running constantly? This compressor powers your cooling system. Advanced repair, allow 2-4 hours for replacement.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Guides airflow across the condenser and secures the fan motor in place. Replace if cracked, broken, or missing to restore proper cooling airflow.

Interior light not turning on or staying on? This master light switch kit restores reliable lighting control in your freezer. Direct-fit assembly.

Refrigerator not cooling or running constantly? A damaged condenser coil prevents proper heat release. This assembly restores cooling efficiency.

Size: 8-32 t. Includes 12 screws.

Condenser air baffle for refrigerators. Directs airflow over the condenser coils. Replace if cracked, broken, or missing to maintain proper air circulation.

Mounting screw for refrigerators and freezers. Secures internal components and panels. Replace if stripped, missing, or damaged during maintenance.

This SCR (silicon controlled rectifier) controls high-current switching in the appliance's power circuit to enable reliable on/off control of heating or motor circuits. Designed for direct replacement of the original SCR component. What it does:

• Acts as a solid-state switch to control power to heating elements or motors when triggered by the appliance control board.
• Helps regulate current during start-up and run cycles to maintain proper operation of the appliance.
• Failures can cause symptoms such as no heat, intermittent operation, or the appliance not powering its load.
• Matches the OEM mounting and stud terminal configuration for proper electrical connection.

• One SCR component (8-32 stud) as pictured.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Use proper tools for the 8-32 stud terminals and ensure secure electrical and heatsink connections.
• Inspect mounting surfaces and replace any damaged hardware or thermal pads as needed for safe operation.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

Left-hand air baffle for refrigerators. Guides airflow between compartments. Replace if cracked, broken, or missing to restore proper air circulation.

Fix a refrigerator that won't cool or runs constantly with this compressor inverter control board. Mounts directly to the compressor for speed regulation.

Refrigerator drier accumulator component that installs in the sealed refrigeration system. Replace if damaged, leaking, or during compressor repairs.

Replacement edge trim that covers and protects exposed edges on refrigerator doors or cabinets. Needed when original trim is cracked, broken, or missing.