Magic Chef Range / Cooktop / Oven Parts

Seal tape restores a tight seal around appliance doors and panels to help prevent air or moisture leaks and improve temperature stability. Use it to replace worn or missing sealing strips that allow drafts, frost, or heat loss. What it does

• Creates a flexible barrier to close small gaps and reduce airflow or moisture migration at door and panel seams.
• Helps maintain correct internal temperatures and can reduce frost buildup or inefficient cooling/heating.
• Replace when tape is cracked, compressed, detached, or visibly deteriorated.
• Commonly used where a thin, form-fitting sealing strip is needed on appliance doors and access panels.

• One seal tape.

• Clean and dry the mating surface before installing for best adhesion; remove old residue.
• Cut to fit and press firmly along the length to seat the tape; trim excess as needed.
• Disconnect power (unplug or switch off breaker) before starting.

This valve kit repairs the appliance's water/control valve assembly and provides the small mounting screw needed for secure installation. It replaces a worn or damaged valve kit so the appliance can restore proper valve function. What it does:

• Replaces the valve assembly components that control water flow or internal fluid routing
• Helps stop issues caused by a damaged valve kit, such as inconsistent water delivery or valve leakage
• Restores secure mounting with the included screw to prevent loose fittings
• Works as the direct replacement kit specified for the original valve location

• Disconnect power and shut off water supply before starting any repair
• Handle valve components carefully to avoid damaging seals and fittings
• Use basic hand tools; avoid overtightening the mounting screw to prevent stripping

This is a replacement thermostat knob that restores safe, easy temperature selection on range and oven controls. The clear indicator and molded grip give reliable adjustment for everyday cooking and baking. What it does:

• Fits onto the thermostat/stove control shaft to set oven or burner temperature
• Replaces cracked, stripped, or missing knobs that are hard to turn or don't stay set
• Provides a visible pointer for accurate temperature selection
• Restores user control when the original knob is worn or damaged

• One black thermostat knob

• Turn power/gas to the appliance off and allow surfaces to cool before installing
• Pull the old knob straight off the control shaft
• Align the knob's splines with the control shaft and push on until fully seated

This replacement igniter knob is the user control that engages the spark igniter and gas valve on compatible gas ranges, restoring safe, reliable burner ignition and user control when the original knob is damaged or worn. What it does:

• Replaces a worn, cracked, or stripped igniter/control knob so you can easily turn burners on and off.
• Engages the burner spark mechanism when rotated or pressed (depending on range design).
• Helps ensure proper alignment with the range valve splines for predictable control response.
• Addresses symptoms like a loose, slipping, or broken knob that won't turn the burner valve or activate ignition.

• One replacement knob

• Disconnect power to the appliance and shut off the gas supply before attempting service.
• Ensure splines on the shaft and inside the knob are clean and undamaged; align knob to the shaft and slide fully onto the splines.
• Do not force the knob onto a damaged shaft; forcing can break the knob or valve stem.
• If the burner does not ignite after installation, the igniter or valve assembly may need inspection—this knob only replaces the user control.

Color: White.

Color: White. Size: 13 oz. Spray paint primer. can.

This clip secures appliance panels or small components to maintain alignment and reduce vibration, restoring the original fit where a worn or broken fastener allows movement or rattling. Simple, direct-fit replacement when the original clip fails. What it does:

• Holds trim, panels, or small components in position to prevent rattling and shifting.
• Replaces broken or missing fasteners that allow loose or misaligned parts.
• Helps keep wiring harnesses or insulation routed and secured in assemblies.
• Small, inexpensive part commonly used wherever a retaining clip is specified.

• Always disconnect power (unplug or shut off circuit) before servicing the appliance.
• Remove panels or trim per the manufacturer service sheet to access the clip; note the clip orientation before removal.
• Use appropriate tools (needle-nose pliers, trim tool) and avoid over-bending the clip or adjacent parts.
• Replace them with the correct OEM-specified clips for reliable fit.

This cooktop is the main top panel for gas units. It supports the burners and grates, helps contain spills, and restores a clean, safe cooking surface when the original top is chipped, dented, or corroded.

• Serves as the primary surface where burner heads, caps, electrodes, and grates mount
• Contains spills and shields internal components from heat and debris
• Restores proper fit if grates or burners no longer sit level
• Typical reasons to replace include chips, cracks, warping, severe staining, or rust

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; note screw locations and igniter lead routing
• Lift off the old top and transfer any brackets, grommets, or insulation as required
• Reassemble carefully and perform a leak check at burner connections after installation

This replacement top burner knob restores smooth, reliable control of your cooktop or range surface burner. Use it to turn the burner on/off and adjust heat when the original knob is cracked, stripped, or missing.

• Mounts on the burner valve or switch stem to control flame/heat level
• Replaces knobs that are broken, loose, or no longer engage the stem
• Helps resolve issues like spinning freely, falling off, or hard-to-set heat
• Restores precise burner control and a clean, finished look

• Allow the appliance to cool; disconnect power and shut off gas before servicing
• Pull the old knob straight off the stem; do not pry on the valve stem
• Align the new knob with the stem and press straight on until fully seated
• The knob markings match the correct burner position before use

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

This is a replacement broil element for the oven's upper heating function. It restores high-heat broiling and top-surface browning so you can sear, brown, and finish foods as intended. What it does:

• Produces the direct, high heat required for broiling and browning
• Replaces a burned-out, visibly damaged, or non-heating upper element
• Restores even top-heat for recipes that require searing or finishing
• Helps eliminate weak or no heat from the oven's broil function

• One broil element

• Disconnect power to the appliance before starting any repair
• Allow the oven to cool completely and use basic hand tools to remove mounting screws and the old element
• Handle the new element carefully to avoid bending or damaging terminals

This replacement igniter knob kit restores the ignition control and user knob for gas range burners, letting you safely operate the burner and re-establish reliable spark control. Designed as a direct-replacement style kit. What it does:

• Replaces the burner igniter control and the user knob assembly used to ignite and adjust a gas burner.
• Helps resolve symptoms such as inability to ignite a burner, intermittent or weak spark, or a loose/missing control knob.
• Restores proper knob feel and control indexing for accurate burner selection.
• Matches OEM form and function for straightforward replacement when the existing knob/igniter assembly is damaged.

• Disconnect power and turn off gas supply before starting any service; follow gas-safety precautions.
• Basic hand tools required; do not force parts—align components before tightening.
• Inspect surrounding components (switch, electrode, wiring) for damage while installing.

This ignition switch controls spark to a gas range burner so burners light reliably when a knob is turned. Replaces a worn or failed switch to restore normal ignition and consistent burner operation. What it does:

• Sends the electrical spark signal to the burner igniter when the control knob is turned
• Allows the range to ignite burners; a failed switch can prevent sparks and burner ignition
• Works with the range's safety/ignition system to enable proper start-up sequencing
• Helps eliminate intermittent sparking or no-spark symptoms linked to a faulty switch

• Disconnect power and turn off the gas supply before beginning service
• Basic hand tools required; access may require removing the cooktop or control panel
• Handle electrical connections carefully and restore grounding; follow manufacturer instructions

This is a set of eight replacement control knobs designed to restore function and appearance to compatible Whirlpool appliances. The kit gives you matching knobs to operate controls and replace cracked, faded, or missing pieces. What it does:

• Replaces worn, cracked, or missing control knobs so you can reliably set cycles, temperatures, or power levels
• Restores a uniform look across the appliance control panel
• Provides a direct-fit replacement for appliances that use the 8-knob kit
• Helps improve grip and control when turning settings

• Remove old knobs by pulling straight off the splined shaft; align new knob spline and push onto the shaft until fully seated
• No special tools typically required; use gentle force to avoid damaging the shaft
• If knobs control electrical functions, ensure appliance controls are off before replacing; disconnect power or gas if advised by the appliance manual

White replacement valve knob that restores safe, reliable control of the appliance valve or control shaft. Molded to match the original fit and feel for easy replacement of cracked, loose or missing knobs. What it does:

• Provides a firm grip for turning the valve or control shaft so settings can be adjusted smoothly
• Replaces cracked, broken, loose or missing knobs that make control difficult
• Restores proper tactile feedback and alignment with the control stem
• Helps prevent accidental slips or improper adjustments caused by a damaged knob

• Always disconnect power and shut off gas or water (when applicable) before servicing the appliance
• Most knobs pull straight off the control stem; inspect for a retaining clip or adapter before removing
• Push the replacement knob onto the stem until it seats fully; verify correct alignment and function before use

This heating element kit replaces a failed heating element to restore normal heating in compatible laundry or cooking appliances. It provides the core heating component needed to get your appliance producing heat again. What it does:

• Replaces a damaged or burned-out heating element that stops the appliance from heating
• Helps resolve symptoms like no heat, weak or inconsistent heating, or tripped thermal cutouts
• Restores the appliance's ability to reach and maintain operating temperatures for normal cycles
• Works as the direct replacement heating component shown in OEM parts listings

• One heating element kit as shown

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock risk
• Handle the element and terminals carefully to avoid bending or damaging mounting tabs
• Confirm correct terminal connections and secure mounting per the appliance wiring diagram