Mastercut Chipper Shredder Parts

Secures hoses to the carburetor on outdoor power equipment engines. Replace if clamp is rusted, broken, or missing to prevent fuel or air leaks.

This is a genuine OEM clamp sourced directly from the manufacturer. It is used in various lawn and garden machines to connect hoses to fittings. It is used to connect piping to water pumps, exhaust pipes to exhaust manifolds, and other similar applications. This connection prevents fluids or air from leaking from the hose. Clamps may be spring or screw/band clamps. Spring clamps require no tools to install and remove; however, the size must be more accurate than when using screw/band clamps. Screw/band clamps are adjustable and can be tightened or loosened. Screw clamps should be inspected periodically to ensure tightness and that the clamps have not rusted.Hose clamps are installed approximately 1/4 inch below the end of the hose. If two clamps are used, there should be 1/4 inch between the two bands. When using a screw clamp, loosen the screw with a screwdriver just enough to fit the clamp over the hose. If using a spring clamp, squeeze the clamp and hold it open. Slide the clamp over the hose and then attach the hose and clamp to the fitting. Slide the clamp into place at the joint and tighten. Do not overtighten. This brass-colored clamp is a spring clamp made of metal; it is sold as an individual unit. This clamp is compatible with many different types of pipes made by various manufacturers.

Exhaust piping connects to the muffler system on small engines. Replace if cracked, corroded, or damaged to restore proper exhaust routing and function.

Hex screw fastener for lawn tractors and outdoor power equipment. Secures components throughout the machine. Replace if stripped, overtightened, or missing.

Insulator plate for lawn tractors and riding mowers. Mounts between engine components to provide heat insulation and proper spacing. Replace if cracked or worn.

Replacement wheel assembly with tire for chipper shredders and lawn equipment. Restores mobility when original wheel is cracked, worn, or broken.

Muffler spark arrestor screen that installs inside the exhaust system. Replace if cracked, clogged with carbon buildup, or missing for safe operation.

Fuel line kit for lawn mowers and outdoor power equipment. Includes tubing and fittings to replace cracked, brittle, or leaking fuel lines in the system.

Muffler assembly that connects to the exhaust tube on lawn mowers and garden equipment. Replace if cracked, rusted, or damaged to restore proper exhaust flow.

Replacement flywheel for small engines. This rotating wheel component stores rotational energy. Order a new one if yours is cracked, rusted, or damaged.

Seals the connection between carburetor and engine to prevent air leaks. Replace if cracked, brittle, or causing rough idle. Verify fit with model number.

Seals the dipstick oil fill tube on mowers and small engines. Replace if leaking oil or cracked to prevent engine damage. Confirm fit by model.

This replacement part is an oil seal. This is a genuine replacement part made by MTD. This part is used to ensure that oil and other fuel cannot escape from the tank. The seal prevents it from leaking during use to ensure the engine is able to run properly. A new oil seal might be needed if the current one has been damaged. If the seal is worn down and thinner than before, it can cause leaks and oil waste. If this is the case, the seal should be replaced immediately. Oil leakage can cause other issues within the machine. Refer to the owner's manual for more information on how to replace this part. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

Connects piston to connecting rod inside the engine cylinder. Replace if pin is stripped, worn, or missing to restore proper piston assembly and movement.

Seals the crankcase halves on lawn mowers and outdoor power equipment. Replace if oil leaks appear or during engine rebuilds. Verify fit by model number.

This is an MTD rocker arm. The rocker arm works in conjunction with the engine and head. The job of the rocker arm is to push the intake valve open, allowing fuel and air to enter the cylinder. Since the rocker arm is a part of the head gasket system, any damage can cause the engine to run extremely weak. There could also be a noticeable clicking or ticking noise originating from the engine area of the mower. A visual inspection of the rocker arm will confirm any damage. Begin the repair by removing the muffler guard. After removal, move to the valve cover and remove that guard as well. Disconnect the fuel and air lines running to the head. Remove the spark plugs in the valve section. Finally, the rocker arm can be removed using a socket wrench. Repeat these steps in reverse to install the new rocker arm.This product is sourced directly from the manufacturer as a genuine OEM part. The component is available individually, separate from the original machine. This part is compatible with MTD and Cub Cadet brand equipment.