Mastercut Tiller Parts

This muffler stud is an OEM part directly sourced from the manufacturer. The muffler stud connects the muffler to the body of the machine. Over time, stress and tension can cause these muffler studs to become loose or even fall out and become lost. Rust and corrosion due to rain and snow can also cause the muffler studs to become loose. When this happens, the studs should be replaced immediately to prevent the muffler from becoming loose or possibly coming off. If the studs are loose and the connection to the machine's engine is not secure, the machine's noise may become louder, or it could emit smoke.If the studs are loose or broken, make sure the engine has cooled down before installing new studs. Use a wrench to tighten loose muffler studs. If the studs are missing, install new ones and tighten them with the wrench. While installing the new studs, it is good to inspect the muffler for holes or damage that may reduce the performance. These muffler studs are made of high-quality steel and are sold individually. These are made to be compatible with tillers and other small engines manufactured by Cub Cadet, MTD, and Yard Machines.

This is a genuine OEM clamp sourced directly from the manufacturer. It is used in various lawn and garden machines to connect hoses to fittings. It is used to connect piping to water pumps, exhaust pipes to exhaust manifolds, and other similar applications. This connection prevents fluids or air from leaking from the hose. Clamps may be spring or screw/band clamps. Spring clamps require no tools to install and remove; however, the size must be more accurate than when using screw/band clamps. Screw/band clamps are adjustable and can be tightened or loosened. Screw clamps should be inspected periodically to ensure tightness and that the clamps have not rusted.Hose clamps are installed approximately 1/4 inch below the end of the hose. If two clamps are used, there should be 1/4 inch between the two bands. When using a screw clamp, loosen the screw with a screwdriver just enough to fit the clamp over the hose. If using a spring clamp, squeeze the clamp and hold it open. Slide the clamp over the hose and then attach the hose and clamp to the fitting. Slide the clamp into place at the joint and tighten. Do not overtighten. This brass-colored clamp is a spring clamp made of metal; it is sold as an individual unit. This clamp is compatible with many different types of pipes made by various manufacturers.

This exhaust piping is a genuine OEM replacement part sourced directly from the manufacturer; it is used on tiller engines and other small engines. The exhaust piping is part of the muffler system. It connects to the exhaust manifold. As gas is combusted to run the engine, it is forced out through the exhaust manifold and the exhaust piping. This process heats the pipes for a short period. Over a period of time, this repeated heating can cause the exhaust piping to deteriorate. If this happens, the piping will need to be replaced in order for the exhaust manifold to function correctly. If the engine is experiencing overheating problems, the exhaust pipes will need to be replaced when it is fixed. Overheating will cause them to deteriorate much faster than normal.Allow the engine and exhaust manifold to cool before replacing the exhaust piping. Remove the exhaust pipes from the exhaust manifold. Inspect the manifold for visible signs of damage while the pipes are off. This would be a good time to replace the exhaust manifold gasket. Install the new pipes. The exhaust piping is made of durable black plastic and sold as an individual unit. It is compatible with tillers, chipper shredders, snowblowers, and other small engines manufactured by Cub Cadet, MTD, Troy-Bilt, and Yard Machines.

This shaft assembly is a genuine MTD part, sold individually. This shaft assembly can be used as a replacement part in a tiller. The purpose of the shaft assembly in a tiller is to provide a shaft upon which the tines can affix so that the tiller can be used to bore into the soil and loosen it for proper gardening and planting.The shaft assembly in a tiller might need to be replaced if it can no longer keep the tines properly affixed or that it suffers enough damage to render it beyond functionality. The shaft assembly could suffer this damage as a result of general wear and tear over long-term use, from a direct impact collision with a hard object such as a rock or a curb, or from exposure to the elements. If this damage occurs, the shaft assembly should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This shaft assembly is compatible with the following outdoor appliance brands: MTD, Ryobi, and Craftsman.

This replacement part is a sprocket assembly intended for use in lawn equipment. This is a genuine replacement part made by MTD. This part ensures that gears and wheels are functioning properly.A new sprocket assembly might be needed if the current one is damaged or broken in any way. It is not unusual for this part to require replacement after years of normal use. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. For more detailed instructions on how to replace this specific part, please reference the user guide or manual for the appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with lawn equipment made by MTD.

This replacement part is an input shaft. It extends from the front of the transmission and carries the drive from the engine. This allows the user to operate the machine properly during use. A new input shaft might be needed if the current one is no longer working. If the engine is struggling during use, it might be time to replace the input shaft. Be sure to wear work gloves when working with the engine to ensure safety during use. This is a genuine replacement part made by MTD. It is an OEM replacement part which will ensure a proper fit. This part is sold individually.

This replacement part is a spur gear. This is a genuine replacement part made by MTD. This small gear is very common in different types of machinery and appliances. There are ridges around the edge that allows it to be connected so that energy is created inside the engine.A new spur gear might be needed if the user notices unusual noises coming from inside the engine. This can mean the spur gear is no longer able to lodge into place and assists in turning other gears. It is common for spur gears to become worn down over time and need to be replaced. Refer to the proper user manual for more information on how to replace this part.This part is a genuine OEM replacement part to ensure proper fit and long-lasting use. This part is sold individually and is sourced directly from the manufacturer.

The breather hose is designed as a valve or vent that only functions one way. It allows air into the fuel tank but ensures that no air or emissions escape the tank. When this hose is not functioning, emissions and air could be leaking from the tank and cause the engine to perform poorly or not perform at all. The hose could become cracked or damaged, or the ends could lose their seal. Either way, a replacement hose will solve the problem and get the equipment back in order. This genuine OEM replacement breather hose is made by MTD and manufactured to exact specifications. It is compatible with several engines on lawn mowers, snowblowers, and chippers from brands like Troy-Bilt, MTD, Yard-Man, Yard Machines, Bolens, Cub Cadet, and Husky. There are more than 150 compatible machines for this breather hose. This high-quality composite rubber hose is sold individually.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.