Maytag Dishwasher Leg Or Foot

These casters replace the base wheels on your appliance, restoring smooth rolling and easy positioning while helping protect floors. Use this 4-pack to refresh worn or missing wheels so the unit moves safely and sits level.

• Provides mobility by supporting the appliance on rolling wheels
• Makes it easier to move the unit for hookup, cleaning, or storage
• Helps maintain a stable, even stance when all casters are intact
• Replace if wheels are cracked, flat-spotted, wobbly/noisy, or missing

• Disconnect power and, if applicable, turn off the water supply; empty the unit before moving
• Protect the floor and get assistance; carefully tip or lay the appliance to access the base
• Remove old casters and install the new ones into the existing sockets/brackets; reuse original hardware if needed
• Set the unit upright, check for smooth rolling, and re-level as required

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This twin-wheel caster replaces a worn or broken wheel on compatible portable appliances and carts, restoring smooth rolling and easier repositioning. A fresh caster helps improve stability and reduces dragging that can scuff floors.

• Supports the unit's weight and lets it roll for cleaning or repositioning
• Twin-wheel design helps distribute load and track smoothly
• Common signs of failure: cracked or missing wheel, caster won't swivel, flat spots, unit hard to move or sits unevenly
• Replacing damaged casters reduces wobble and noise when rolling

• Disconnect power and shut off water. Empty the unit as needed before moving.
• Carefully tip or elevate and support the appliance to access the caster; use a helper to avoid injury.
• Remove the retaining fastener/clip, transfer any spacers, and install the new caster in the same orientation.
• After installation, verify all casters are seated, the unit rolls smoothly, and it sits level.

The Leveling Leg is an OEM part for Whirlpool dishwashers. It is an adjustable leg that is used to level the dishwasher and stabilize it when installed under the kitchen counter or inside cabinetry.  

Causes of a bad leveling leg often relate to normal wear and tear over time, repeated adjustments, or potential overtightening that leads to thread damage.

Symptoms of a bad leveling leg include:

• The dishwasher is not sitting level and appears unstable  
• Leaks occurring around the dishwasher perimeter or door seal
• Drainage or pooling of water inside the dishwasher
• Cabinetry or countertops showing scratches or wear

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This Leveler is the adjustable foot that supports and levels your appliance. Replacing a worn, cracked, or missing leg helps stop rocking and vibration, improving stability and ensuring smooth, quiet operation.

• Screws into the base to set height and keep the appliance level and secure
• Helps reduce rocking, vibration, and rattling that can cause excess noise
• Supports proper alignment and smooth door/closure operation when level
• Common symptoms: appliance wobbles, leg is stripped or broken, difficult to keep unit level

• Disconnect power and shut off gas/water if applicable before servicing
• With help, tip or lift the appliance slightly and protect the floor
• Thread the new leveler into the mounting boss and adjust height with a level
• Verify the unit is stable by gently rocking and recheck level after initial use