Maytag Range Bumper, Bushing, Grommet Parts

This bumper is a small cushioning stop used at contact points on the appliance. It absorbs impact and prevents metal-to-metal contact to reduce noise and protect surfaces when doors, drawers, lids, or racks close.

• Cushions closing to soften impact and protect finishes
• Serves as a stop to maintain proper spacing at the contact point
• Helps reduce slamming, squeaks, and rattles
• Replace if cracked, flattened, missing, or if new clunking noises occur when closing

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the bumper's original location and orientation
• Remove the old bumper and clean the mounting area or hole
• Press the new bumper fully into place and verify a secure fit and proper clearance

This spacer is a small mounting component that helps keep internal appliance parts correctly positioned for reliable, quiet operation. Use it to restore proper spacing and reduce rubbing or vibration between parts. What it does:

• Provides correct spacing between components to maintain alignment and prevent contact
• Helps reduce noise and vibration caused by misaligned parts
• Supports stable assembly of panels, brackets, or housings where used
• Commonly replaced when worn, cracked, or missing

• Disconnect power (and water, if applicable) before beginning any repair
• Installation typically requires removing an access panel and replacing the old spacer with the new one
• Use basic hand tools; avoid forcing parts into position to prevent damage

This small replacement bumper cushions contact points to reduce noise, prevent wear, and help doors or panels close more quietly and sit flush. Use it to restore proper cushioning where an original bumper is worn or missing. What it does:

• Absorbs shock and prevents metal-to-metal contact that can cause noise or chipping
• Helps doors, panels, or components close more softly and remain properly seated
• Reduces vibration transferred to surrounding parts for quieter operation
• Restores protective spacing to prevent rubbing and premature wear

• Disconnect power to the appliance before servicing and follow the manufacturer's safety instructions
• Typically installs at the contact point; remove the old bumper and press or place the replacement into position
• If the bumper uses adhesive or a fastener, use the same method indicated by the OEM for secure fitment

This small rubber bumper cushions and stabilizes moving appliance parts to reduce vibration, noise and wear. It restores proper spacing where a worn or missing stop lets components rub or rattle. What it does:

• Acts as a soft stop to prevent metal-on-metal contact and dampen vibration
• Helps eliminate rattling or scraping noises from doors, drawers or panels
• Maintains correct alignment and spacing of moving parts
• Protects finishes and extends service life of mating components

• Typically pressed or snapped into a socket or mounting post; no special tools usually required
• Clean the mounting area of dirt and residue before installing for best adhesion/fit
• Ensure the bumper is the correct match and fully seated before operating the appliance
• Disconnect power when working near electrical or moving parts

This snap-in bushing provides a low-profile bearing surface to support rotating shafts and reduce wear and noise in appliance assemblies. It restores smooth operation where the original bushing is worn or damaged. What it does:

• Provides a replaceable bearing/sleeve for rotating shafts and posts
• Reduces friction and wear on housing and moving parts
• Helps eliminate rubbing, grinding, or rattling noises during operation
• Maintains correct shaft alignment for smooth rotation

• One snap-in bushing

• Disconnect power before servicing and follow all safety instructions
• Access may require removing panels or covers; inspect surrounding parts for wear
• Press or snap the bushing squarely into the housing until fully seated; avoid deforming it
• Replace any damaged retainers or seals and test operation after reassembly

This replacement bumper cushions and protects appliance panels and doors to reduce vibration, prevent chipping, and stop rubbing or rattling. It restores a quiet, secure fit where the original bumper has worn or fallen off. What it does:

• Acts as a soft stopper to prevent doors, drawers, or panels from banging or contacting metal surfaces
• Reduces vibration and rattling during operation
• Protects finishes from chips, scratches, and wear at contact points
• Helps restore proper alignment and snug fit where the original bumper is missing or compressed

• One replacement bumper (1 count)

• Clean and dry the mounting surface; remove any old adhesive or debris before installing
• Press the bumper firmly into place; some bumpers use adhesive backing or fit into a recess—verify fit before final placement
• If adhesive is used, allow time for proper bonding per adhesive instructions; avoid using the appliance until secure
• For safety, disconnect power to the appliance before accessing panels or doors