Maytag Range Fuse Or Sensor

• Oven is too hot
• Little to no heat when baking
• Won't start
• Little to no heat when broiling

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

First, don't self clean your oven before the holidays. In fact, read up on what damage the self cleaning feature can do to your oven. How did I fix it, I went on line and saw the comments of appliancepartspros.com. I figured out that it was the thermal fuse that probably went wrong since my oven just went lights out after the cleaning. My oven is a Kitchenaid model # KEBS179BSSOO. The part for this model is AP6022801 or WPW10545255. I spoke with technical support but I still had questions. I... Read more

Replaced the blown heating element. I also only to be on the safe side, replaced the over temp sensor. I checked it with the meter when I pulled it out and it was ok. Tested ok. Thank you very much for the less than 2 day delivery on the part. Read more

• Door won't open after self cleaning cycle
• Element will not heat
• Little to no heat when baking
• Won't start

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

Replaced the thermst-fix and the thermal fuse oven now works great Read more

Replaced fuse. It took much longer to get the oven out of the wall to access the fuse and replace the front panel than to do the repair. This fuse failed at the end of the cleaning cycle for the bottom oven and left the door locked because the open fuse removed the 120v power from the control board. The locked door made it impossible to remove one of the screws holding the wall oven in place. However, after I ground off the head of the screw behind the edge of the locked door I was able to... Read more

• Won't start

I have a Jenn-Air microwave that didn't turn on and had no lights. It just stopped working completely. I unplugged the unit and had to remove the rear cover using a *security screw kit* that prevents people from opening the rear panel. Once opened, I removed the fuse and testing it with an OHM reader to determine that the fuse went bad. But I also had to determine why the fuse blew and noticed a sticky oily substance under the Capacitor. I used a rubber glove and needle nose pliers to... Read more

Tested the High Voltage Capacitor which showing no capacitance and no resistance. Replaced it together with the diode and the line fuse no longer blew and the microwave is back in service. Read more

Thermostat was broken, was a quick easy fix thanks. Read more

I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more

Lid switch problem. Easy to fix, not so easy to diagnose. First thing to look at if something goes wrong and there does not appear to overtly be mechanical issue like pump, etc. Read more

Easy replacement after filing two flats on the you can't get the back off screws. Read more

I was devastated to hear my wife tell me our Whirlpool double oven was dead after she used the self clean mode. After my research, I found this problem to be more common than expected. I kept seeing reference made to Appliance Parts Pros during my research. I went to the website and found the parts I didnt think anyone had. APP was quick, the price was excellent and when I called their staff I found them to be friendly, knowledgeable and thorough! They had my parts to me in no time and I fixed... Read more