Maytag Range Wire, Harness, Power Cord

This replacement dryer power cord supplies electricity from your wall outlet to the dryer's terminal block, providing a secure, reliable connection. Replace a worn or damaged cord to restore dependable power and reduce risk of intermittent shutoffs.

• Supplies electrical power from the outlet to the dryer
• Provides a secure connection at the plug and the dryer's terminal block when properly installed
• Common fixes: dryer won't power on, power cuts out when the unit is moved, or visible damage/heat discoloration on the cord or plug
• Replace if prongs are loose or the insulation is cracked or melted

• Disconnect power at the breaker before servicing and verify the outlet is de-energized
• Follow the dryer's wiring diagram; connect conductors to the correct terminals and tighten securely
• Use an approved strain relief/clamp per the dryer instructions and local electrical codes

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This contact assembly restores a reliable electrical connection within an appliance's control circuit. Replacing worn or pitted contacts helps eliminate intermittent operation and arcing so the controlled component can turn on and off consistently. What it does

• Provides the conductive interface that completes the circuit when the control is engaged
• Helps deliver stable power to the connected load
• Typical failure signs: intermittent operation, no operation of the controlled component, visible heat damage/pitting on contacts, arcing or buzzing at the contact point

• 1 contact assembly

• Disconnect power to the appliance before servicing and verify no voltage is present
• Access the control area; photograph or label wire positions and terminal orientation
• Move wires one at a time to the new assembly; ensure tight, clean connections
• Inspect nearby wiring for heat damage and replace any burnt terminals; test operation before reassembly

This factory wire harness is the pre-terminated wiring assembly that links key components inside your appliance. Replacing a damaged harness restores reliable electrical connections and can help resolve dead, intermittent, or erratic operation of individual functions. What it does:

• Distributes power and signals between the control and components such as motors, switches, heaters, sensors, and lights
• Provides model-specific, correctly keyed connectors and lengths for secure, clean routing
• Helps correct issues from burnt, broken, pinched, or corroded wires and loose/melted connectors
• Symptoms can include components not running, intermittent operation, error codes, or visible heat damage at connectors

• 1 wire harness assembly

• Disconnect electrical power before servicing; if applicable, also shut off water or gas supplies
• Photograph existing routing and connections to match the original layout during reassembly
• Route the new harness away from sharp edges, moving parts, and hot surfaces; secure with existing clips/ties
• Seat each connector fully until locked; inspect mating terminals for heat damage and address as needed

This supply cord assembly connects the appliance to household power using 18-gauge wiring and a factory-installed push-tie strain relief, replacing a damaged or frayed cord to restore a safe, reliable connection. What it does:

• Provides the electrical connection between the appliance and the outlet using 18 AWG conductors.
• Secures and routes the cord with a built-in push-tie strain relief to help prevent wiring stress.
• Replaces cords that are cut, frayed, burned, or causing intermittent power.
• Restores reliable power delivery when a damaged cord is the source of power loss or flickering.

• One supply cord assembly (18 ga) with factory-installed push-tie.

• Always disconnect power at the breaker or unplug the appliance before servicing.
• Match wire colors and secure connections per the appliance wiring diagram; ensure the push-tie/strain relief is seated properly.
• After installation, restore power and verify normal operation; if issues persist, stop and consult service.

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

This replacement power cord restores the appliance's main AC connection so it can receive power safely. Use this cord when the original cable is frayed, cut, melted, or otherwise damaged to prevent intermittent power or electrical hazards. What it does:

• Replaces the appliance's factory power cable to restore reliable electrical connection.
• Transmits mains power from the outlet to the appliance's internal wiring and controls.
• Addresses symptoms such as no power, intermittent power loss, visible cord damage, or burn/melt marks at the cord or plug.
• Helps prevent electrical arcing or shorting caused by damaged insulation or exposed conductors.

• Disconnect the appliance from power at the breaker or unplug before starting any work.
• Verify the cord matches the appliance's connector and routing; do not modify cord ends or splices.
• Secure all strain reliefs and terminal connections per the appliance's service instructions.

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

This wire harness routes power and signals between an appliance's controls and components to restore reliable electrical connections. Replacing a damaged harness helps eliminate intermittent or failed electrical paths and unsafe wiring. What it does:

• Carries power and control signals between the control board and components.
• Restores proper electrical connections when wires or terminals are burned, frayed, or broken.
• Commonly used to address intermittent operation, failure to start, or components not responding.
• Helps prevent shorts or arcing caused by damaged insulation or loose terminals.

• Disconnect power before starting any repair.
• Compare connectors and wire routing to the original; replace only if identical.
• Disconnect and reconnect connectors by hand; avoid pulling on wires. Use proper tools when needed.
• Follow OEM wiring diagrams and secure routing/clamps to prevent chafing or heat exposure.

The Harness-Wire is an OEM part for Whirlpool ranges. It serves as the wiring harness that connects electrical control boards and sensors within the range. 

 Symptoms of a bad harness-wire include:

• Elements or burners that do not heat 
• Issues with switches, controls, or displays failing to work properly
• Recurring range or oven component malfunctions

Causes of a bad harness-wire can be damage from excessive flexing/bending over time, moisture leading to shorts, or failure of crimp/solder connections along the wire.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes electrical power and signals between components to restore reliable operation. It replaces a damaged or worn harness to help stop intermittent power, control issues, or components that won't activate. What it does:

• Connects power and control circuits between the control board and major components
• Restores proper electrical continuity when original wiring is frayed, burned, or broken
• Helps resolve intermittent operation, no-power conditions, or unresponsive controls caused by damaged wiring
• Maintains factory routing and connector fit for correct function and safety

• One complete wire harness as shown

• Disconnect all power before starting work to avoid shock or damage
• Verify connectors are fully seated and routed per original path; replace any damaged clips or retainers
• Inspect mating connectors and terminals for corrosion or heat damage; repair both sides if needed