Maytag Wall Oven Hinge Parts

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays properly aligned, helping the door seal engage correctly for safe, reliable operation.

• Supports the weight of the door and controls opening/closing motion
• Helps maintain door alignment so latches/seals engage properly
• Wear or damage can cause sagging, rubbing, squeaking, or difficulty closing
• A misaligned door may prevent the unit from starting or sealing correctly

• Disconnect power and allow the appliance to cool before servicing
• Use gloves and eye protection; doors can be heavy and spring-loaded
• Support the door during removal to prevent damage
• Transfer any hardware from the old hinge to the new one if re-usable

This upper oven door hinge is a position-specific hinge that supports and controls a side-swing door's movement, helping it open smoothly and seal firmly. Replacing a worn hinge restores proper alignment, closure, and heat retention.

• Provides the pivot and spring action at the door's upper mounting point
• Maintains door alignment for proper gasket contact and heat seal
• Typical symptoms of a failing hinge: door won't close fully, sags, binds/rubs, or pops open
• A poor seal from a worn hinge can lead to heat loss and uneven baking

• Disconnect power and allow the oven to cool completely before service
• Support the door; many models require removing the door to access the hinge
• Install at the factory mounting points and ensure the hinge fully engages the receiver
• After replacement, check door alignment and that the seal contacts evenly

The door hinge is an OEM part for Whirlpool ranges. This piece serves as the anchor for stable, smooth opening and closing of the oven door. 

Causes of a bad door hinge include warping from repeated heat exposures and compromising its secure gateway function over time. Breakdowns disrupt workflows. 

Symptoms involve: 

• A sagging oven portal is unable to support itself when ajar  
• Grating or binding movements straining the hinge mechanism
• Difficulty latching or sealing the door during baking

This OEM Whirlpool part is also compatible with some Maytag, Jenn-Air, and KitchenAid ranges.

Right side hinge receiver for door hinge. For left side hinge receiver use WP4455605.

This Door Hinge supports and pivots the appliance door for smooth operation and a square, reliable close. Replacing a worn hinge restores alignment so the door seals properly and opens and closes without binding or noise. What it does

• Supports door weight and provides the pivot point for opening and closing
• Maintains proper door alignment to help ensure an even gasket seal
• Restores smooth, consistent door movement
• Common symptoms: door droops or rubs, squeaks/grinds, or won't close flush

• Includes 1 door hinge

• Disconnect power before servicing
• Support the door and use a helper; remove contents as needed to reduce weight
• Mark hinge position and transfer any spacers/bushings in the same order
• Tighten mounting fasteners, then check alignment and gasket contact; adjust as needed

Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.

This hinge receptacle mounts in the oven cabinet and provides a secure receiver for the door hinge arm. Replacing a worn receptacle restores smooth hinge engagement and helps the door close and seal correctly.

• Receives and secures the oven door hinge in the appliance frame
• Maintains proper door alignment for consistent closing and sealing
• Common symptoms: door won't close fully or stay closed; door sags or feels loose; difficulty reinstalling the door; visible wear or deformation at the receiver
• Also referred to as a hinge receiver/bracket in some catalogs

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door; hinge springs are under tension—use caution
• Remove the old receptacle from the cabinet and install the new one using existing fasteners, aligning the slot with the hinge arm
• Reinstall the door and verify smooth engagement and full closure

This is a replacement oven door hinge that supports and controls the swing of the oven door for smooth opening and secure closing. Restoring the hinge helps the door seal properly, improving heat retention and overall cooking performance.

• Supports the oven door's weight and movement
• Helps the door close fully to engage the gasket
• Worn hinges can cause sagging, misalignment, or a door that won't stay closed
• Also lead to heat loss and longer preheat times

• Disconnect power and allow the oven to cool completely before service
• Remove the door per your model's manual; support the door to prevent strain on the glass
• Transfer any locking clips/brackets as required by the model
• Test door operation and seal engagement after installation

This oven door hinge supports and guides the door through its range of motion so it opens smoothly and seals tightly when closed. Replacing a fatigued hinge restores proper door alignment and consistent oven performance. What it does:

• Provides spring-assisted tension to control door opening and closing
• Helps the door seal evenly against the gasket to retain heat
• Maintains correct stop positions to prevent slamming or over-travel
• Common symptoms: door won't close fully or pops open, drops/slams, sits crooked, heat escaping/long preheat

• One door hinge assembly

• Disconnect power at the breaker; allow the oven to cool completely before servicing.
• Remove the door per your model's procedure (often open to the broil stop, engage hinge locks, then lift off).
• Use hinge locks/pins to control spring tension and prevent snap-back during removal/installation.
• Support the door to avoid damage; many replace both hinges together to keep tension balanced.

This replacement door hinge restores smooth, stable door movement and proper alignment. Replacing a worn hinge helps the door open and close correctly so the appliance seals as designed and operates safely.

• Provides the pivot point for opening and closing the door
• Helps maintain door alignment for a consistent, reliable seal
• Replaces a bent, loose, or worn hinge that affects door operation
• Common symptoms: door sags, won't close fully, pops open, binds, or squeaks

• Disconnect power; turn off gas or water supply before servicing
• Support the door during removal and installation to prevent damage or injury
• Compare the new hinge to the original and transfer any reusable hardware
• After installation, check door alignment and closure; adjust per your model's service instructions

The Hinge-Door is an OEM component specifically designed for Whirlpool gas ranges. It is the stainless steel door hinge assembly that allows smooth, controlled movement of the oven door. The hinges support the weight of the door and maintain proper alignment between the door and oven cavity.

Symptoms of bad door hinges include:

• Loose, wobbly, or sagging door that does not stay firmly in place
• Difficulty in fully opening or closing the door 
• Excessive noise or vibration from the hinges
• Pinholes, cracks, or other damage to the hinge surface

Causes of failure are typically wear over the heavy usage life of a range. Hinges may also become misaligned or damaged by accidental impact.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely. Replacing a worn hinge restores proper alignment and sealing to help the door latch correctly and operate as designed.

• Provides the pivot point and maintains door alignment
• Helps ensure smooth opening/closing and proper latching
• Supports a tight seal to prevent gaps, rattles, or temperature/moisture loss
• Typical failure signs: door sags, binds, squeaks, or won't stay closed/aligned

• Disconnect power before service; wear gloves to protect from sharp edges
• Support the door and control any spring tension; remove mounting hardware and the old hinge
• Install the new hinge in the same orientation; transfer any reusable hardware
• Adjust as needed

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays aligned with the latch and gasket. Replacing a worn hinge restores proper fit and closing action to reduce rubbing and poor sealing.

• Provides the pivot point and supports the door's weight during operation
• Maintains alignment for an even gap and consistent seal
• Helps correct sagging, scraping, or a door that won't close flush
• Common signs of wear: bent/cracked hinge, squeaking or popping, misalignment

• Disconnect power before servicing and support the door to prevent strain or damage
• Remove mounting fasteners; transfer any reusable screws, spacers, or covers from the old hinge
• Install and snug fasteners, then check door alignment and closure; adjust as needed
• Open and close the door several times to verify smooth operation and recheck fasteners

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal