Maytag Washer Dryer Combo Parts

This right-side door hinge rebuilds a worn or damaged pivot point so the appliance door opens, closes and seals properly. It restores door alignment and prevents sagging that can cause gaps and cooling loss. What it does

• Replaces the right-side door pivot to restore correct door swing and alignment
• Reduces door sag and helps maintain an even seal to improve temperature retention
• Stops rubbing, scraping or binding that can occur with a worn hinge
• Works with the existing hinge housing and fasteners when used as a direct replacement

• One right-side door hinge (single hinge)

• Install with power to the appliance off and interior removed as needed for safe access
• Support the door during replacement to prevent dropping or additional damage
• Use the OEM fasteners and torque to manufacturer recommendations; inspect surrounding parts for wear

High limit thermostat, Canadian models only.

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

This replacement clamp secures flexible hoses and lines to prevent leaks and keep connections tight. It restores a secure seal so appliances move water or air without escaping at the joint. What it does:

• Secures inlet, drain or water lines to fittings and housings
• Helps stop leaks from loose or worn hose connections
• Keeps hoses from slipping off during operation or vibration
• Commonly replaced when clamps are corroded, broken, or no longer hold tension

• Inspect hose and fitting for damage before installing the new clamp
• Position clamp over the hose barb and tighten evenly until snug; avoid over-tightening
• Use appropriate tools (pliers or clamp driver) and follow appliance safety procedures
• Disconnect power and shut off water supply when working on water lines

A replacement latch spring that helps the appliance door latch return and hold securely, restoring reliable door engagement and proper cycle starts. Fits the original latch mechanism and installs quickly for common latch-related issues. What it does:

• Provides tension for the door latch so the strike stays engaged during operation
• Restores proper door closing and helps prevent door from popping open mid-cycle
• Commonly used when the latch feels loose, the door won't stay closed, or cycles won't start
• Works with the appliance's existing latch assembly to return the latch to its resting position

• One spring for the door latch

• High-level replacement: remove access panel or door trim to reach the latch assembly
• Handle spring under tension carefully and wear eye protection to avoid injury
• If other latch components are damaged or worn, replace the entire latch assembly for a reliable repair
• Unplug the appliance or disconnect power before starting any repair

This drum baffle replaces a worn or damaged lifter inside the dryer drum to help clothes tumble evenly and prevent items from bunching. Restores proper tumbling and reduces rubbing/snags caused by broken or missing lifters. What it does:

• Lifts and separates clothes as the drum turns to promote even drying
• Helps prevent garments from tangling or bunching in the drum
• Reduces fabric rubbing and potential snags caused by damaged lifters
• Commonly replaced when the original is cracked, loose, or missing

• One drum baffle

• Disconnect power before starting repairs
• Removal of the dryer drum or front panel is typically required; follow model-specific service instructions
• Use appropriate hand tools and keep track of mounting screws/clips for reassembly
• Inspect drum, mounting studs, and fasteners; replace any stripped or damaged hardware for a secure fit

This left-side door hinge restores correct door support and movement so the appliance door opens and closes smoothly. It replaces a worn or bent hinge that can cause sagging, misalignment, or noisy operation. What it does:

• Supports the left side of the appliance door and maintains proper alignment
• Enables smooth, controlled opening and closing of the door
• Replaces a bent or broken hinge that causes door sag or rubbing
• Helps prevent gaps that can affect door sealing or operation

• Disconnect power (or unplug) and remove any panels as instructed by the manufacturer before starting
• Support the door during removal and installation to prevent injury or damage
• Use proper tools and follow the appliance service manual for torque and fastener locations

This replacement axle/latch spring secures the latch/axle assembly so the appliance door or panel stays engaged during use. It restores proper latch tension for reliable closing and operation. What it does:

• Applies tension to the latch/axle so the door or access panel stays closed and latched
• Helps ensure the appliance detects a closed door and will start or run normally
• Common symptom: door won't stay closed or latch feels loose or fails to engage
• Small metal spring designed for a specific latch assembly — not a universal part

• Disconnect power to the appliance before starting any repair
• Access may require removing a panel, bezel, or door — use proper tools and keep fasteners organized
• Handle the spring and latch components carefully; springs are under tension and can snap free

This hex nut secures fasteners on compatible Whirlpool appliances to keep panels and components held firmly in place. It's a simple replacement that stops loose parts and restores proper fit and function. What it does:

• Threads onto corresponding bolts or studs to lock panels, brackets, or assemblies.
• Stops vibration-related loosening that can cause rattling or misaligned parts.
• Helps re-secure components after service or collision damage.
• Use when the original nut is stripped, missing, or damaged.

• Disconnect power and unplug the appliance before servicing electrical components.
• Use the correct size socket or wrench to avoid rounding the nut.
• Tighten securely but do not overtighten; replace with matching thread and grade if specified by the OEM.
• If the original fastener was seized or damaged, inspect the mating bolt/stud and replace as needed.