Parts for Ge JE1660SA02: 01 - Section1 Parts

This glass tray is a flat oven shelf that provides a smooth, easy-to-clean surface for baking and roasting. It restores a stable cooking surface and replaces cracked, chipped, or otherwise damaged oven glass trays. What it does:

• Supports bakeware and cookware for even heating on the oven floor or shelf area
• Replaces trays that are cracked, chipped, or shattered and may cause uneven cooking
• Provides a smooth, non-porous surface that's simple to wipe clean
• Helps prevent food drips from contacting the oven floor when used as intended

• One glass tray

• Handle carefully; glass can break and cause injury—wear cut-resistant gloves
• Allow the oven to cool completely before removing or installing the tray
• Inspect tray for chips or stress cracks before first use; do not use if damaged
• Follow the appliance manufacturer's instructions for placement and safe use

Lower door hinge for microwaves. Secures the bottom of the door to the cabinet frame. Replace if cracked, broken, or causing door misalignment.

Replace your microwave's door hinge pin if the original is broken, bent, or missing. This small rod secures the door hinge assembly for smooth operation.

This wire harness routes power and signals between the appliance control and electrical components to restore reliable electrical connections. It replaces worn or damaged wiring to help restore proper operation. What it does:

• Connects control board to components using molded connectors
• Replaces frayed, burned, or broken wiring that can cause intermittent or no power
• Helps stop component failures caused by loose or corroded connections
• Restores original factory routing and connector fit for consistent performance

• One wire harness

• Always disconnect power (unplug or shut off breaker) before starting service
• Compare the replacement harness to the old part for connector types and routing before installing
• Use existing clips and fasteners to secure the harness; avoid pinching or sharp edges

The Microwave Door Switch is an OEM part for GE microwaves, designed to prevent the microwave from operating when the door is open by interrupting the power whenever the door is not securely closed. The door switch is an essential safety feature.

Symptoms of a failing Microwave Door Switch include:

• The microwave not starting or heating
• Running when the door is opened
• Unusual noises when the door is closed  

Causes of a bad Microwave Door Switch can result from repeated opening and closing of the door or slamming that can cause the switch to degrade or become misaligned, leading to intermittent or failure.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Monitor Switch is an OEM replacement part for GE microwave ovens. Located internally on the turntable control circuit board, this switch monitors rotation of the turntable during cooking cycles.  

Causes of failure involve degradation of the electrical contacts from continuous arcing loads over years of use combined with vibration stresses.

Symptoms of a faulty monitor switch include:

• The turntable no longer rotates or spinning intermittently
• Cooking cycles aborting prematurely with error messages 
• Screeching or grinding noises emanating from beneath cavity
• Visible burnt spots on turntable drive assembly

This genuine GE switch is also compatible with select Hotpoint and RCA models.

This Supporter - mgt is a small mounting support that helps secure and stabilize the appliance assembly where it attaches. It reduces movement and keeps related components aligned for reliable operation. What it does:

• Provides structural support for the appliance assembly and helps hold parts in position
• Reduces rattling, vibration, and movement caused by loose or worn supports
• Helps maintain proper alignment of adjacent panels or components
• Can prevent further wear or damage resulting from a loose assembly

• Disconnect power to the appliance before starting any repair
• Remove any trim or panels that block access to the mounting location
• Typical installation requires basic hand tools (screwdriver, nut driver); keep fasteners organized

Microwave not heating but runs? Replace the magnetron to restore cooking power. Intermediate DIY repair taking 1-2 hours with proper safety steps.

This power cord assembly provides the main electrical connection for the appliance, restoring safe, reliable power delivery when the original cord is damaged or fails. Designed to match the OEM connection type and fit. What it does:

• Delivers mains power from the wall outlet to the appliance's terminal block
• Replaces frayed, cut, or heat-damaged power cords that can cause loss of power
• Helps stop symptoms like the appliance not powering on, intermittent power, or visible cord damage
• Restores a proper grounding/neutral connection when the cord or terminals are compromised

• Always disconnect power at the breaker and verify the appliance is de-energized before servicing
• Secure the cord with the appliance's strain relief or clamp to prevent stress on the electrical terminals

This part has been discontinued and is no longer available.

The Fuse is an OEM part for GE microwaves. It serves as a safety device designed to protect the microwave from excessive current that can cause overheating and potential fire hazards. When the current flowing through the microwave circuit exceeds a certain level, the fuse blows or breaks, cutting off the power to prevent damage or fire.

Common causes for a fuse to blow include power surges, faulty wiring within the appliance, or the use of microwave inappropriate containers that cause sparks. It is essential to address these issues not only to replace the fuse but also to correct the underlying problems to prevent future failures.

Symptoms of a bad fuse include:

• The microwave suddenly stops working.
• No signs of power or response even when the microwave door is closed and the start button is pressed.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Microwave not heating or humming loudly? The high-voltage diode converts AC to DC for the magnetron. Repair takes 30-45 minutes with basic tools.

This gas flame sensor detects whether a burner's flame is present so the range/oven's gas valve and ignition control can operate safely. It helps restore reliable ignition and prevents the valve from staying open when no flame is detected. What it does:

• Senses the presence of a gas flame and signals the control to keep the valve open
• Helps prevent gas flow if a flame is not detected
• Can stop ignition or cause the oven/range not to heat when failing
• Commonly replaced when burners won't stay lit or control shows ignition-related errors

• One gas flame sensor

• Turn off electrical power and shut off the gas supply before servicing
• Handle the sensor and its connector carefully to avoid damage
• Reinstall in the exact position and orientation; loose connections can cause false faults

Fix a microwave that won't heat or has no power with this low voltage transformer. Common repair for dead displays and control panel issues.

This oven door assembly replaces a damaged or worn door to restore safe sealing and consistent cooking performance. The complete unit includes the door structure and attached components for one direct swap. What it does

• Replaces a cracked, bent or otherwise damaged oven door to help restore proper heat retention
• Stops drafts, uneven cooking or heat loss caused by a warped or broken door
• Eliminates rattling, loose trim or gaps from a failing door assembly
• Restores a secure latch and proper alignment so the oven closes reliably

• One complete oven door assembly

• Disconnect power and allow the oven to cool completely before starting
• Support the door weight; use a second person to remove and install the assembly
• Keep fasteners and hinges aligned; tighten securely but avoid over-torquing
• Handle carefully and replace damaged seals per OEM instructions