Parts for Ge JEB1050BV01: 01 - Section1 Parts

Microwave not heating or heating unevenly? A failed magnetron is the likely cause. This high-voltage tube generates microwave energy to cook food.

Ceramic

This control board cover is a replacement protective shield designed to sit over the appliance control assembly and help prevent debris, moisture, and accidental contact with electrical components. It restores the factory protection and appearance of the control area. What it does

• Covers and protects the control board and wiring from dust, spills, and physical contact
• Helps prevent short circuits and component damage caused by loose debris or accidental impact
• Restores proper fit and finished look to the control area when the original cover is cracked, warped, or missing
• Matches OEM fit and mounting points so the control assembly sits securely

• One control board cover

• Disconnect power to the appliance before attempting any repair to avoid shock
• Remove any trim or access panels as needed to reach mounting screws; keep hardware for reinstallation
• Align cover to existing mounting points and secure with original screws; do not overtighten

Fix a microwave that won't heat or hums but doesn't start. This capacitor stores energy for the high-voltage circuit. Moderate DIY repair, 30-60 minutes.

Microwave not heating or humming loudly? The high-voltage diode converts AC to DC for the magnetron. Repair takes 30-45 minutes with basic tools.

This high-voltage transformer supplies the ignition voltage used to create sparks for gas burner/oven ignition. Replaces a worn or failed transformer to restore reliable spark firing and consistent burner ignition. What it does:

• Converts line vo

This gas flame sensor detects whether a burner's flame is present so the range/oven's gas valve and ignition control can operate safely. It helps restore reliable ignition and prevents the valve from staying open when no flame is detected. What it does:

Temperature probe socket for microwaves. Connects probe to control board. Replace if socket is cracked, broken, or fails to hold probe securely.

A replacement wire harness for the refrigerator temperature probe. Restores the electrical connection between the probe and control so the appliance can monitor temperature accurately. What it does:

• Connects the temperature probe to the refrigerator control board or harness
• Allows the control to read temperature signals from the probe
• Can resolve temperature-related errors or inconsistent cooling when the harness is damaged
• Replaces frayed, burned, or disconnected wiring between the probe and control

• One wire harness for the probe

• Disconnect power to the appliance before starting any repair
• Match connector orientation and secure all plugs until they click
• Route and secure the harness away from sharp edges and heat sources

This cord bushing provides a protective seal where the appliance power cord passes through the cabinet, preventing chafing and reducing strain on the cord. It restores a safe cord entry and helps maintain proper cord alignment. What it does

• Protects the power cord from rubbing against sharp edges or metal panels.
• Helps prevent electrical shorts and exposed wiring caused by worn or damaged openings.
• Reduces cord movement and strain at the entry point to the appliance.
• Commonly replaced when the cord shows wear at the cabinet or when the bushing is cracked or missing.

• One cord bushing

• Turn off power to the appliance (unplug or switch off circuit breaker) before inspecting or replacing the bushing.
• Install by seating the bushing in the cord entry hole and routing the cord through; ensure the bushing sits flush and the cord moves freely without pinching.
• Use basic hand tools; no special wiring changes are required for this part.

Illuminates your microwave interior for monitoring food during cooking. Replace when bulb burns out or dims. Verify fit with your model number before ordering.

This lamp bracket is the replacement mounting support that secures the oven/cabinet lamp assembly so the light stays in position and the bulb remains stable during use. Restores proper lamp alignment and helps prevent rattling. What it does:

• Holds the lamp socket or lamp assembly firmly in place inside the oven or appliance cavity
• Keeps the bulb aligned so the light properly illuminates the interior
• Prevents vibration and rattling that can occur with a broken or bent bracket
• Compatible with the original lamp mounting location to allow simple reinstallation

• One replacement lamp bracket

• Turn off power to the appliance and disconnect from the electrical supply before starting
• Handle the lamp and socket carefully; remove the bulb before removing the old bracket
• Installation usually requires basic hand tools (screwdriver); keep fasteners removed from the old part for reuse if undamaged

Door latch lever slider for microwaves. Replaces cracked, broken, or worn sliders that prevent the door from closing securely or latching properly.

Replace your microwave's door slider lever if the original is broken, cracked, or missing. This lever component installs inside the door mechanism.

The Microwave Door Switch is an OEM part for GE microwaves, designed to prevent the microwave from operating when the door is open by interrupting the power whenever the door is not securely closed. The door switch is an essential safety feature.

Inner door frame for microwave doors. Installs between the outer door panel and glass. Replace if cracked, damaged, or warped to restore door structure.

If your microwave door won't stay closed or latch properly, this door key actuator engages the latch assembly to restore secure closure during operation.

This part has been discontinued and is no longer available.

Replaces a cracked, broken, or missing door slot cover on your microwave. This protective guard installs on the door panel to maintain proper appearance.

Support plate that mounts and secures the power control module inside your microwave. Replace if cracked, broken, or missing to properly hold the control board.

Small spacer that positions and stabilizes the oven rack inside the microwave cavity. Replace when worn, missing, or cracked to restore proper rack height.