Parts for Ge JEB1095BB01: 01 - Microwave Parts

If your microwave runs but won't heat food or makes grinding noises, the magnetron has likely failed. Moderate DIY repair requiring capacitor discharge.

This 250V 15A safety fuse protects the appliance's line circuit from overcurrent. When the original fuse has blown, replacing it can restore power and help safeguard internal components from further damage.

• Opens the circuit if excessive current

This control board cover is a replacement protective shield designed to sit over the appliance control assembly and help prevent debris, moisture, and accidental contact with electrical components. It restores the factory protection and appearance of the control area. What it does

• Covers and protects the control board and wiring from dust, spills, and physical contact
• Helps prevent short circuits and component damage caused by loose debris or accidental impact
• Restores proper fit and finished look to the control area when the original cover is cracked, warped, or missing
• Matches OEM fit and mounting points so the control assembly sits securely

• One control board cover

• Disconnect power to the appliance before attempting any repair to avoid shock
• Remove any trim or access panels as needed to reach mounting screws; keep hardware for reinstallation
• Align cover to existing mounting points and secure with original screws; do not overtighten

This damper cam engages the refrigerator air damper assembly to help control airflow between compartments, restoring proper vent movement and temperature balance. It replaces a worn or broken cam that prevents the damper from opening or closing correctly. What it does:

• Fits into the damper/actuator assembly to transfer motion from the damper motor to the vent
• Helps regulate airflow between fresh food and freezer compartments
• Commonly replaces a cracked, stripped, or broken cam that causes vents to stick
• Can resolve symptoms like uneven cooling, warm spots, or vents that won't open/close

• Disconnect power to the appliance before starting any repair
• Access may require removing interior panels or the damper housing; keep track of screws and clips
• Handle plastic gears and cams carefully to avoid damage during installation
• After installation, restore power and verify the damper cycles and vents move normally

Wire harness for microwaves. Connects electrical components inside the appliance. Replace if wires are frayed, damaged, or connections are loose or broken.

Fix a microwave that won't heat or hums but doesn't start. This capacitor stores energy for the high-voltage circuit. Moderate DIY repair, 30-60 minutes.

Microwave not heating but lights and timer work? The high voltage diode converts AC to DC for the magnetron. DIY repair in 1-2 hours with basic tools.

Mounting bracket for microwaves. Secures and supports the microwave cabinet installation. Replace if bent, broken, or missing during reinstallation.

This high-voltage transformer supplies the ignition voltage used to create sparks for gas burner/oven ignition. Replaces a worn or failed transformer to restore reliable spark firing and consistent burner ignition. What it does:

• Converts line vo

Fix sensor cook cycles that won't adjust properly or show sensor errors. This humidity sensor monitors moisture levels for automatic cooking adjustments.

Temperature probe socket for microwaves. Connects probe to control board. Replace if socket is cracked, broken, or fails to hold probe securely.

A replacement wire harness for the refrigerator temperature probe. Restores the electrical connection between the probe and control so the appliance can monitor temperature accurately. What it does:

• Connects the temperature probe to the refrigerator control board or harness
• Allows the control to read temperature signals from the probe
• Can resolve temperature-related errors or inconsistent cooling when the harness is damaged
• Replaces frayed, burned, or disconnected wiring between the probe and control

• One wire harness for the probe

• Disconnect power to the appliance before starting any repair
• Match connector orientation and secure all plugs until they click
• Route and secure the harness away from sharp edges and heat sources

Illuminates your microwave interior for monitoring food during cooking. Replace when bulb burns out or dims. Verify fit with your model number before ordering.

This lamp bracket is the replacement mounting support that secures the oven/cabinet lamp assembly so the light stays in position and the bulb remains stable during use. Restores proper lamp alignment and helps prevent rattling. What it does:

• Holds the lamp socket or lamp assembly firmly in place inside the oven or appliance cavity
• Keeps the bulb aligned so the light properly illuminates the interior
• Prevents vibration and rattling that can occur with a broken or bent bracket
• Compatible with the original lamp mounting location to allow simple reinstallation

• One replacement lamp bracket

• Turn off power to the appliance and disconnect from the electrical supply before starting
• Handle the lamp and socket carefully; remove the bulb before removing the old bracket
• Installation usually requires basic hand tools (screwdriver); keep fasteners removed from the old part for reuse if undamaged

This left side trim restores the finished edge on the appliance door, replacing a cracked, broken or missing trim piece to improve appearance and protect the door edge from damage. What it does:

• Covers and protects the outer edge of the door for a finished look
• Replaces cracked, warped or missing left-side trim
• Helps prevent dirt and debris buildup along the door edge
• Restores the original exterior appearance after impact or wear

• Turn off power to the appliance before starting work as a safety precaution
• Remove door shelves or panels as needed for access per your model's service instructions
• Use gentle, even pressure and a non-marring tool to snap or slide the trim into place
• Replace damaged fasteners or clips before reinstalling trim

Door latch lever slider for microwaves. Replaces cracked, broken, or worn sliders that prevent the door from closing securely or latching properly.

Replace your microwave's door slider lever if the original is broken, cracked, or missing. This lever component installs inside the door mechanism.

Fix a microwave that won't start or runs with the door open. This momentary contact switch restores reliable door sensing. Direct-fit replacement.

This door bracket secures the appliance door to its hinge/mount so the door opens, closes and stays aligned. It replaces a worn or damaged bracket to restore proper door support and smooth operation. What it does:

• Provides a secure mounting point between the door and hinge assembly
• Restores proper door alignment and prevents sagging or uneven gaps
• Reduces door movement and rattling during operation
• Helps ensure an airtight seal when the door is closed

• Disconnect power (and water, if applicable) before starting any repair
• Handle door and surrounding trim carefully to avoid scratching or breaking glass
• Use the original screws or OEM-recommended fasteners; torque snugly but avoid over-tightening

A direct-replacement refrigerator door handle that restores a secure grip and smooth opening. Replaces a cracked, broken or loose handle so the door operates safely and looks finished. What it does

• Provides a firm, ergonomic grip for opening and closing the refrigerator door
• Replaces cracked, broken or bent handles that are difficult or unsafe to use
• Prevents wobbling or loose movement caused by stripped or missing mounting hardware
• Restores proper door handling and appearance

• Disconnect power to the appliance and empty the door area before starting
• Typical installation requires accessing door mounting screws—use the correct screwdriver or bit
• Keep track of any trim, gaskets or brackets removed and reinstall in the original order
• Do not overtighten screws; tighten until secure to avoid cracking the handle

Inner door frame for microwave doors. Installs between the outer door panel and glass. Replace if cracked, damaged, or warped to restore door structure.

If your microwave door won't stay closed or latch properly, this door key actuator engages the latch assembly to restore secure closure during operation.

Color: Bisque

Color: White

Color: Stainless Steel

Color: Black

Replaces a cracked, broken, or missing door slot cover on your microwave. This protective guard installs on the door panel to maintain proper appearance.

This small terminal pin connects a wire to an appliance's electrical terminal, restoring a secure electrical connection so components receive reliable power and operation. Ideal for repairing loose or damaged wire terminations. What it does:

• Provides a secure metal contact point for a wire at a terminal or connector
• Restores proper electrical continuity when a terminal end is worn, bent, or broken
• Helps eliminate intermittent power, arcing, or component failures caused by poor connections
• Used wherever a single-pin wire termination is required on the appliance harness

• Disconnect power before servicing to avoid shock or injury
• Remove the damaged terminal and ensure the replacement pin matches shape and size
• Crimp or seat the pin per OEM guidance; ensure a snug, corrosion-free connection
• If wiring or harness insulation is damaged, replace the harness

This support bracket secures and stabilizes internal appliance components, helping keep assemblies aligned for reliable operation. Fits where a small metal bracket is needed to hold panels, rails or internal frames in place. What it does

• Provides structural support to hold parts and panels in position
• Prevents shifting, rattling or misalignment of mounted assemblies
• Restores secure attachment when a bent, cracked or missing bracket causes looseness
• Works as a replacement for a single small metal support bracket used in the appliance's interior

• One support bracket (exact quantity as shown on product page)

• Install with basic hand tools; match hole pattern and orientation to existing bracket
• Power off and unplug the appliance before accessing internal parts
• Retain all fasteners unless replacements are provided; reuse OEM screws where appropriate
• If corrosion or other damage is present on mating surfaces, clean and inspect before installing the new bracket

Support plate that mounts and secures the power control module inside your microwave. Replace if cracked, broken, or missing to properly hold the control board.

Small spacer that positions and stabilizes the oven rack inside the microwave cavity. Replace when worn, missing, or cracked to restore proper rack height.

Lower trim panel for microwaves. Replaces cracked, broken, or missing lower trim pieces. Restores the finished appearance of your microwave exterior.