Mixer Parts

Color: stainless. It measures about 3-1/2 inches wide by 6 inches high.

A replacement whip wire that restores the electrical connection between the appliance wiring harness and the power/element circuit for reliable operation. Helps address intermittent power, poor connections and arcing at the connector. What it does:

• Provides a dedicated insulated lead to carry voltage between the main harness and the controlled component
• Replaces cracked, burned or frayed wiring that can cause intermittent power or component failure
• Eliminates loose or corroded connector ends that create poor contact or arcing
• Restores a safe, secure electrical connection when the original wire or terminal is damaged

• Disconnect power at the breaker or unplug the appliance before starting any work
• Secure wire away from moving parts, sharp edges and high-heat surfaces using existing clips or fasteners

Fixes mixer that won't turn or makes grinding noises. This gearcase assembly transfers motor power to beaters. Moderate DIY repair, 1-2 hours.

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This spur gear is a direct-drive replacement gear that transfers rotary motion between motor and transmission components, restoring correct gear engagement and part movement in compatible appliances. What it does:

• Replaces a worn or stripped drive gear to restore proper mechanical engagement
• Helps eliminate slipping, erratic part movement, or loss of driven function
• Can stop grinding or clicking noises caused by damaged gear teeth
• Works as a direct mechanical link between motor/drive components and the driven assembly

• Disconnect power and water before any disassembly
• Requires disassembly of the drive/transmission housing; refer to OEM service manual for steps
• Inspect mating gears and shafts for wear—replace any damaged parts to prevent repeat failure
• Use only recommended lubricants per OEM guidance; do not force-fit or modify the gear

Threaded nut secures panels, brackets, and internal assemblies in your stand mixer. Replace if missing, stripped, or damaged to restore secure attachment.

This 6 Wire Whip incorporates air into ingredients for fluffy whipped cream, perfect for frostings and cakes with whipped egg whites. Fits KitchenAid 3.5 Quart Tilt Head models KSM3306, KSM3311, KSM3316, KSM3317, 5KSM3310, 5KSM3311, 7KSM3311, 9KSM3311.

The 7 Quart Commercial Stainless Steel Dough Hook can knead yeast dough with ease. This KitchenAid Dough Hook fits 7 and 8 Quart models KSM7588, KSM7589, KSM7990, KSM8990, KSMC895, 3KSMC895, 4KSM7990, 5KSM7580, 5KSM7590, 5KSM7990, 5KSMC895, 9KSM7990, 9KSMC895.

Protects and secures hinge or pivot pins on mixer attachments. Replace if cracked, broken, or missing to prevent metal wear and keep pins properly seated.

6-quart wire whip attachment for stand mixers. Whips air into cream, frostings, and egg whites. Replace your cracked, bent, or missing whip.

This is a replacement door gasket that seals the dishwasher door to help prevent leaks and keep wash water inside the tub. Restores a tight door seal for reliable cleaning and less mess. What it does:

• Creates a watertight seal between the dishwasher door and tub to stop leaks during cycles
• Helps maintain proper wash pressure and prevents water from leaking onto the floor
• Reduces chance of detergent residue and water spotting on the floor or cabinetry
• Commonly replaced when the door leaks, water puddles near the door, or the seal is cracked or compressed

• One replacement door gasket

• Disconnect power and shut off the water supply before beginning any repair
• Follow the manufacturer's disassembly steps for removing the door inner panel or trim—handle panels gently to avoid damage
• Inspect the door cavity and mounting channel; clean and dry before installing the new gasket for best fit
• After installation, run a short test cycle and check for leaks; re-torque any fasteners to manufacturer specs if required

This genuine wire whisk replaces a damaged or missing mixing beater to restore whisking and light mixing performance for compatible Bosch hand mixers and stand attachments. It provides reliable aeration for batters and egg whites. What it does:

• Replaces a worn or bent wire whisk used to whip cream, beat eggs, and mix light batters
• Restores even mixing and improved aeration for better texture
• Helps eliminate uneven or slow mixing caused by damaged beaters
• Fits into the mixer's beater socket to engage with the drive for normal operation

• One replacement wire whisk (single beater)

• Always unplug the appliance before removing or installing attachments
• Remove the old beater by pressing the eject/release button or twisting per your mixer's method, then insert the replacement until it clicks or seats securely
• Test operation briefly at low speed to confirm proper engagement before full use
• Inspect for damage before each use and discontinue use if the whisk is bent or wires are loose

The door catch lever is the mechanism that securely latches the appliance door in the closed position during operation. This component ensures the door stays firmly shut and activates safety switches when properly engaged. Replace it when the door won't stay closed, pops open during cycles, or the appliance won't start due to door latch issues.

This blender drive rod transfers motor rotation to the blade assembly so your blender mixes ingredients efficiently. It's a direct-replacement part that restores proper coupling between the motor shaft and blender jar. What it does:

• Connects the motor's output to the blender blade assembly so the jar rotates and blends
• Restores reliable transfer of torque when the original rod is bent, worn, or broken
• Helps eliminate slipping, wobbling, or inconsistent blending caused by a damaged rod
• Works as the mechanical linkage inside countertop blender units that use a removable jar/drive system

• Disconnect power before servicing and remove the blender jar and blade assembly
• Inspect seals, couplers, and adjoining components for wear; replace damaged parts as needed
• Reassemble carefully, ensuring the rod seats correctly in the drive coupler and blade assembly
• Test on low speed first to ensure proper engagement and quiet operation

Wire harness assembly for stand mixers. Connects internal electrical components. Replace if wires are frayed, damaged, or connections are loose or burnt.