Parts for Frigidaire LCG751LL1: 04 - Motor And Blower Parts

Specs: 8 - 18 x 0.500

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

Specs: 8 - 18 x 0.500

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

PPH ab st/z/ch `6 - 18x.60

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Hex washer head ,10-32 x 0.375. Ground

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

This part has been discontinued by the manufacturer and is no longer available.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Blower wheel clamp

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A replacement union hex nut that secures a refrigerator water line or tubing to a mating valve or fitting, restoring a tight, leak-free connection. Simple, serviceable fastener used on water and refrigeration line unions. What it does

• Secures tubing or line to a mating union fitting or valve to maintain a sealed connection
• Stops leaks at the union when worn or damaged nuts allow seepage
• Helps restore proper water flow to dispenser or ice maker when connection is the cause
• Works with compatible refrigerator water and refrigeration line unions

• One union hex nut

• Shut off the refrigerator water supply before starting work
• Tip: loosen slowly and re-tighten by hand then wrench to avoid overtightening and damaging tubing
• If replacing a corroded nut, inspect the ferrule/sleeve and mating fitting and replace if damaged

This genuine OEM replacement part is a gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential functions. If the dryer is no longer drying clothes effectively, or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is an easy fix.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old valve assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles. 

Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines. 

Symptoms of a faulty ignitor can include:

• The dryer fails to start or stop heating intermittently   
• Cycles taking overly long to complete or feel uneven
• Excessive service calls relating to "no heat" troubles  
• Risk of uncombusted gas pooling in dryer if ignition falters

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Dryer Heat Sensor is an OEM part for Frigidaire dryers. This sensor monitors the temperature inside the dryer drum to ensure clothes are dried effectively and safely by regulating the heat levels during the drying cycle.

Causes of a bad heat sensor can include wear and tear from frequent use, buildup of lint or debris, or electrical issues. A malfunctioning sensor can result in incorrect temperature readings, leading to under-drying or overheating of clothes.

Symptoms of a bad Dryer Heat Sensor include:

• Clothes not drying properly or taking too long to dry
• Dryer overheating or shutting off unexpectedly
• Inconsistent drying cycles
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part