Parts for Ge DCVH485EK0MS: 05 - Motor & Blower Parts

This blower wheel nut secures the dryer blower wheel to the motor shaft, keeping the wheel stable for proper airflow and drying. A simple replacement that stops wobble and helps restore quieter, more efficient operation. What it does:

• Holds the blower wheel firmly on the motor shaft to prevent slipping or wobbling
• Prevents noise caused by a loose blower wheel
• Helps maintain consistent drum airflow for better drying performance
• Reduces wear on the blower assembly by keeping parts aligned

• Disconnect power before starting any repair to avoid shock or injury
• Access may require removing the dryer front panel or blower housing depending on model
• Typically removed/installed with a socket or pliers; hold the blower wheel to prevent spinning while tightening
• Tighten securely but avoid over-torquing to prevent thread damage

The BLOWER WHEEL ASSEMBLY is an OEM part for GE electric dryers. It contains both the blower wheel and blower motor housing. This assembly powers the rotation of the blower wheel to generate crucial airflow through the dryer. During cycles, it circulates heated air to enhance drying performance.

Symptoms of a bad blower wheel assembly include:

• Dryer not drying clothing properly, cycles taking excessively long  
• Absence of any air blowing through the dryer ducting
• Loud buzzing or grinding noises from the blower motor area
• Significant accumulation of lint in the exhaust duct or around duct openings

Causes of failure can be a worn or damaged blower wheel, broken motor windings, or blocked air passages within the housing over multiple years of use. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Thermostat is an OEM part for GE dryers. It monitors air temperatures inside the dryer drum during cycles to ensure they remain within a designated safe range. As a safety component, the thermostat automatically cuts power if temperatures get too high, protecting dryer components from damage.

Causes of a bad thermostat can include normal wear and tear over time from repeated heat cycles. Mineral buildup interference or electrical faults may also cause premature malfunction.

Symptoms of a faulty thermostat include:  

• Inability to properly heat or maintain consistent air temperatures
• Unexpected fluctuations outside of set temperature points   
• Issues fully completing designated drying cycles  
• Potential overheating errors or safety trips

This genuine OEM GE replacement thermostat restores accurate temperature monitoring and controls. Compatible with some Hotpoint, RCA, and Kenmore models as well, it improves performance reliability and safety once installed. Replacing a faulty component prevents ongoing operational issues.

The Thermistor Assembly is an OEM part for GE dryers. As an integrated sub-assembly, it includes multiple temperature-monitoring thermistors to comprehensively sense heat throughout cycles. 

Located in air inlets and outlets, these thermistors provide feedback to regulating components like the control board and heating elements. This allows for consistent thermal operation by maintaining intended temperatures.

Causes of failure can be normal component wear over repeated heat cycles. Mineral buildup, electrical faults, or accidental mishandling may also prematurely impact functioning.

Symptoms of a faulty thermistor assembly include: 

• Inability to properly heat or maintain consistent air temperatures
• Unexpected fluctuations outside of set points
• Issues fully completing designated drying cycles
• Potential safety trips from inaccurate temperature readings

This genuine GE replacement ensures precise thermal regulation is fully restored. Compatible with some Hotpoint, RCA, and Kenmore dryer models as well, safety and performance reliability are improved.

The Idler Bracket and Bearing Assembly is an OEM part for GE dryers. This assembly supports and guides the dryer drum belt, ensuring it remains tensioned and aligned for proper drum rotation during the drying cycle. The idler bracket and bearing play a crucial role in maintaining the efficiency and functionality of the dryer.

Over time, the idler bracket and bearing can wear out or become damaged. Causes of a bad idler bracket and bearing assembly can include frequent use, physical damage, or normal wear and tear of the moving parts.

Symptoms of a bad Idler Bracket and Bearing Assembly include:

• Squeaking or grinding noises during the drying cycle
• The dryer drum not turning smoothly or at all
• Increased drying times or incomplete drying

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This idler spring secures and tensions the dryer drum/idler assembly to maintain proper belt alignment and drum rotation. Replacing a worn or broken idler spring restores correct tension for smooth, consistent drying performance. What it does:

• Applies tension to the idler pulley to keep the drive belt tight and aligned.
• Helps prevent the belt from slipping, dragging, or coming off the drum.
• Reduces unusual squeaks, rubbing noises, and irregular drum movement caused by a failed spring.
• Works as part of the idler/drive assembly that ensures even drum rotation.

• Disconnect power (and gas if applicable) before starting any repair.
• Inspect the idler pulley, belt, and mounting hardware while replacing the spring; replace any visibly damaged parts.
• Use caution when releasing or installing tensioned components to avoid pinch injuries.

The Motor Assembly is an OEM component specifically designed for GE laundry machines. This assembly contains the motor and blower wheel that are responsible for forcing air through the dryer and circulating hot air around clothes during the drying cycle. 

Causes of a bad motor assembly can include wear and tear over time, exposure to high heat cycles that can depreciate motor insulation or bearings, or damage due to impact or mishandling. 

Symptoms of a bad motor assembly include:

• The dryer not heating or only heating intermittently  
• Loud grinding or knocking noises originating from the motor area
• The blower wheel no longer spins or turns slowly
• Extended drying times 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Idler Bracket and Bearing Assembly is an OEM part for GE dryers. This assembly supports and guides the dryer drum belt, ensuring it remains tensioned and aligned for proper drum rotation during the drying cycle. The idler bracket and bearing play a crucial role in maintaining the efficiency and functionality of the dryer.

Over time, the idler bracket and bearing can wear out or become damaged. Causes of a bad idler bracket and bearing assembly can include frequent use, physical damage, or normal wear and tear of the moving parts.

Symptoms of a bad Idler Bracket and Bearing Assembly include:

• Squeaking or grinding noises during the drying cycle
• The dryer drum not turning smoothly or at all
• Increased drying times or incomplete drying

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is an M3 x 16 mm machine screw used to fasten small appliance components. It provides secure, low-profile attachment for panels, brackets, and assemblies, restoring proper fit and preventing rattles or looseness. What it does:

• Secures panels, brackets, or small components to appliance frames and assemblies
• Restores proper alignment and eliminates vibration or rattling caused by missing or loose fasteners
• Replaces stripped, missing, or corroded screws to maintain safe equipment operation
• Works where a metric M3 x 16 mm threaded fastener is specified by the manufacturer

• Use the correct screwdriver or bit to avoid stripping the head
• Thread components by hand first, then snug; do not overtighten
• Replace any damaged mating hardware (nuts, captive clips) for secure fastening
• Disconnect power and follow appliance safety procedures before servicing

The Drive Belt is an OEM part for GE dryers. This belt wraps around the dryer drum, the tension pulley, and the motor pulley, enabling the drum to rotate during the drying cycle. It ensures the effective tumbling of clothes for efficient drying.

Causes of a bad drive belt can include normal wear and tear over time, excessive friction, or overloading the dryer, which can lead to the belt stretching, fraying, or breaking.

Symptoms of a bad drive belt include:

• The dryer drum not spinning
• A squealing or thumping noise during operation
• Clothes taking longer to dry
• The dryer stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Idler Bracket and Bearing Assembly is an OEM part for GE dryers. This assembly supports and guides the dryer drum belt, ensuring it remains tensioned and aligned for proper drum rotation during the drying cycle. The idler bracket and bearing play a crucial role in maintaining the efficiency and functionality of the dryer.

Over time, the idler bracket and bearing can wear out or become damaged. Causes of a bad idler bracket and bearing assembly can include frequent use, physical damage, or normal wear and tear of the moving parts.

Symptoms of a bad Idler Bracket and Bearing Assembly include:

• Squeaking or grinding noises during the drying cycle
• The dryer drum not turning smoothly or at all
• Increased drying times or incomplete drying

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.