Parts for Magic Chef MD258: 05 - Motor, Heater & Spray Arm Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Dishes not getting clean or poor spray action? This wash impeller and seal kit restores water circulation through spray arms for proper cleaning.

This O-ring is a small rubber sealing gasket that prevents water leaks at a refrigerator water connection. It restores a watertight seal to stop drips and maintain proper water flow to the dispenser/ice system. What it does:

• Creates a watertight seal at a water line or valve connection
• Helps stop visible dripping or slow leaks from fittings
• Maintains proper pressure and flow by preventing bypass around a joint
• Used where a compressible seal is required between two mating parts

• Shut off water supply and disconnect power before servicing
• Replace only with the correct-size O-ring and seat it evenly in the groove
• Inspect mating surfaces for nicks or debris; clean before installing the new O-ring
• Tighten fittings to manufacturer torque recommendations to avoid over-compression

This component circulates water throughout the dishwasher's lower wash arm and prevents leaks at the connection point. Located at the bottom of the dishwasher tub, it should be replaced if you notice poor cleaning performance, unusual noises during wash cycles, or water pooling beneath the unit.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

This rubber grommet cushions and secures appliance components where they pass through panels or mount to frames, reducing vibration and protecting wiring or hoses from abrasion. It helps restore quiet operation and stable mounting. What it does:

• Cushions mounts and reduces vibration or rattling from motors or panels
• Protects wires, hoses, and tubing from chafing where they pass through openings
• Keeps components properly positioned to prevent wear and noise
• Worn or missing grommets can cause rubbing, vibration noise, or movement of parts

• One rubber grommet as shown

• Disconnect power to the appliance before servicing
• Remove the damaged grommet and install the replacement in the same orientation
• No special tools typically required; small pliers or a flat tool can help seat tight grommets
• Inspect surrounding seals, wiring, and mounting hardware while replacing

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Mounting washer for dishwasher installation and assembly. Replace if washer is missing, cracked, or worn to ensure secure fastening of components.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Replacement mounting screw for various appliances. Needed when original screws are stripped, lost, or damaged during repair or maintenance work.

Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.

This part has been discontinued by the manufacturer and is no longer available.

Replace your dishwasher's spray arm spindle if the original is cracked, broken, or worn. This mount secures the spray arm hub to the dishwasher base.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.