Parts for Electrolux EFME517STT0: 05 - Motor Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replace your dryer's cabinet mounting spacer if cracked, broken, or missing. Maintains proper clearance between panels and components inside the cabinet.

Replacement refrigerator door gasket that restores a tight seal around the door to help maintain proper temperatures and reduce energy loss. Designed as a direct-fit replacement to stop air leaks and improve cooling performance. What it does:

• Seals the door perimeter to prevent cold air from escaping and warm air from entering
• Helps reduce frost build-up and condensation inside the compartment
• Restores consistent temperature for better food preservation
• Can improve energy efficiency by eliminating gaps that cause the compressor to run more

• Unplug the appliance or turn off power before beginning work
• Remove the old gasket by loosening retainer screws or pulling it free from the door channel per your model's service instructions
• Seat the new gasket fully into the door channel; warm it with a hair dryer or hot water (carefully) if needed to improve flexibility and fit

This replacement refrigerator door gasket seals the door to help maintain proper temperature and reduce energy loss. It restores a tight seal around the door edge for more consistent cooling and food freshness. What it does

• Forms a weather-tight seal around the refrigerator door to help keep cold air in and warm air out
• Helps reduce frost buildup and energy waste from a failing or torn seal
• Common symptom: visible gaps, torn or brittle gasket, or warm spots near the door edge
• Works as a direct-fit replacement when the factory gasket is worn, cracked, or misshapen

• Disconnect power to the appliance before attempting replacement
• Clean the door flange and seating area before installing the new gasket for best seal
• Soften and shape the gasket as needed (warm water or gentle heat can aid flexibility) and ensure the magnetic edge seats fully

Replacement screw for securing dryer trim, panels, and interior components. Needed when original fastener is lost, stripped, or damaged during repair.

Dryer won't start or shuts off mid-cycle? This thermal fuse cuts power when overheating occurs. Common fix for E63, E66 errors. DIY repair under 1 hour.

Dryer making loud rumbling or tapping noise? A worn or damaged blower wheel assembly is often the cause. Moderately difficult repair for most DIYers.

Dryer not drying evenly or taking too long? This blower assembly circulates air for proper airflow and consistent drying. Restores performance.

Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.

Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.

Threaded fastener that secures and spaces dryer components. Replace if the original spacer screw is missing, stripped, or damaged during repairs.

Replacement pulley that guides the drive belt in your dryer. Needed when the original pulley is worn, seized, cracked, or causing belt damage.

Idler spring attaches to the idler arm to maintain proper belt tension. Replace if spring is broken, stretched, or missing to restore correct tension.

Idler arm assembly mounts near the dryer drum to guide and tension the belt. Replace if the pulley is worn, cracked, or causing belt misalignment issues.

Transfers motor power to rotate the drum. Replace if dryer hums but won't spin or makes squealing sounds. Verify fit with your model number.

Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.

Dryer won't start or drum won't turn? A failed motor is often the cause. This motor drives the drum and blower. Moderate DIY repair, 1-2 hours.

The Bracket is an OEM part for Frigidaire clothes dryers. Internally installed, this L-shaped bracket securely anchors heavy rotating components like the belt pulley assembly and motor in correct alignment.

Causes of failure could include fatigue cracks from years of absorbing vibration stresses during active cycles. Corrosion risks increase further with repeated heating and moisture exposure over time as well.

Symptoms of a problematic bracket consist of:

• Noisy operation or shaking felt within the dryer 
• Components detaching or rotating out of intended position
• Visible cracks compromising secure mounting integrity

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.