Parts for Frigidaire TDB668RBS0: 06 - Motor Pump Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Replacement screw for dishwasher assembly and mounting. Used to secure components throughout your dishwasher. Replace if stripped, missing, or damaged.

This screw fastens the heater bracket to the appliance, providing a secure mount for the heating assembly. Replacing a worn or missing screw helps keep the bracket stable and maintains proper heater positioning. What it does:

• Secures the heater bracket to the cabinet or housing to hold the heating element in place
• Prevents bracket movement that can cause rubbing or vibration noises
• Reduces risk of intermittent heating caused by a loose heater assembly
• Helps maintain correct alignment of the heater and related components

• Disconnect power (and gas for gas models) before beginning any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Handle sharp sheet-metal edges carefully and follow all appliance safety instructions

Dishes not drying properly? Your dishwasher heating element may have failed. This element heats water and dries dishes during the final cycle. DIY fix.

Fix poor water spray and dishes not getting clean with this dishwasher wash impeller kit. Replaces worn or broken impellers with missing fins.

Replacement dishwasher filter chopper blade that grinds food particles in the sump assembly. Replace if dishes aren't cleaning well or you hear grinding noise. Verify fit by model number.

This O-ring is a small rubber sealing gasket that prevents water leaks at a refrigerator water connection. It restores a watertight seal to stop drips and maintain proper water flow to the dispenser/ice system. What it does:

• Creates a watertight seal at a water line or valve connection
• Helps stop visible dripping or slow leaks from fittings
• Maintains proper pressure and flow by preventing bypass around a joint
• Used where a compressible seal is required between two mating parts

• Shut off water supply and disconnect power before servicing
• Replace only with the correct-size O-ring and seat it evenly in the groove
• Inspect mating surfaces for nicks or debris; clean before installing the new O-ring
• Tighten fittings to manufacturer torque recommendations to avoid over-compression

Dishwasher pump gasket seals the circulation pump to prevent leaks. Replace if you notice water pooling under the dishwasher. Verify fit with your model.

This pump housing encloses the dishwasher's wash or drain pump motor assembly and directs water flow through the system during wash and drain cycles. It includes mounting hardware and provides a sealed chamber for proper pump operation. Replace this housing if it is cracked, leaking from the bottom of the dishwasher, or if the pump is not circulating or draining water effectively due to housing damage.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

This washer heater assembly heats and maintains wash water temperature to improve detergent performance and cleaning for temperature-sensitive cycles. Designed as a direct replacement part for compatible top- and front-load machines. What it does:

• Heats incoming water to reach selected cycle temperatures for better soil removal.
• Helps maintain water temperature during the wash portion of the cycle.
• Common symptom: washer runs but water stays cold or loads are not cleaned as expected.
• Common symptom: water temperature error codes or washer fails temperature-sensitive cycles.

• Disconnect power and water supply before starting any repair.
• Handle the heating element and wiring with care; avoid damage to terminals and gasket surfaces.
• Installation may require removal of access panels and basic hand tools.
• After installation, restore power and run a short test cycle to check for leaks.

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Watershield assembly for dishwashers. Protects internal components from water damage. Replace if cracked, warped, or missing to prevent leaks.

Motor mounting screw for dishwashers. Secures the motor assembly to the frame. Replace if missing, stripped, or damaged during motor service or repair.

Dishwasher filter chopper assembly that grinds food particles and prevents drain clogs. Replace if water won't drain or pump runs without emptying. Verify fit with your model number before ordering.

Protective shield that covers the dishwasher spray arm assembly. Replace this guard if it's cracked, broken, or missing to protect spray arm components.

Seals the filter housing assembly to prevent leaks in your dishwasher. Replace if cracked, worn, or causing water leakage during cycles.

O-ring seal for dishwashers prevents leaks at pump and filter connections. Replace when cracked, brittle, or leaking. Confirm fit with model number.

Replacement mounting screw for dishwashers. Secures panels, components, and internal parts. Order a new screw if yours is stripped, missing, or damaged.

This part has been discontinued by the manufacturer and is no longer available.

This side mounting bracket kit includes the hardware needed to secure a dishwasher to the adjacent cabinetry from the sides rather than from the countertop. It is commonly used in kitchens with granite, stone, or other countertops where top-mounting screws cannot be used. Replace this kit if the original brackets are bent, broken, or missing, causing the dishwasher to shift or slide during operation.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.