Parts for Husqvarna 967303601-00: Mower Deck / Cutting Deck Parts

This replacement part is a deck belt intended for use in lawn equipment. This is a genuine replacement part made by Husqvarna. Deck belts link various rotating shafts to ensure that the entire machine is running smoothly and efficiently. A new deck belt might be needed if the current one is damaged or broken in any way such as being split or torn. The user might be able to tell when the deck belts are malfunctioning if there are noises coming from the machine that are not typical. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. It is recommended that the user refer to the appliance manual for more detailed instructions on how to install this part. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with lawn equipment made by Husqvarna.

This replacement part is a wire harness and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Wire harnesses are an important part in many lawn equipment engines. They are responsible for connecting different parts of the machine so they everything runs smoothly and efficiently. A new wire harness might be needed if the user notices that some parts of the appliance are not working properly. It is normal for wire harnesses to become inoperable after years of normal wear and tear as wires are often damaged. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This 16.25 inch-long blade is manufactured for use with lawn mowers, lawn tractors, zero-turn mowers, and riding mowers. It is a genuine Husqvarna part. The blade is a crucial component of the mower. It is the part that actually cuts grass. It is normal for the blade to become dull over time. They can be sharpened, but replacing will yield better results.Before replacing the blade on a mower, allow the engine to cool, empty the fuel tank, and disconnect the spark plug for safety. Wear work gloves to protect the hands. Tip the lawnmower onto its handle assembly or side. Use a socket to remove the nuts or bolts that attach the blade to the mower. Replace with the new blade and torque the nuts and bolts.This blade is a genuine OEM part sourced directly from the manufacturer. It is sold individually, and most mowers have only one cutting blade. It is manufactured to be compatible with several models made by Dixon, Husqvarna, and Jonsered.

This replacement part is a discharge chute, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. A discharge chute allows the user to operate the lawn mower with ease while ensuring that the grass clippings and debris are exposed of in the proper direction. If the current discharge chute is missing or damaged, the user might notice that grass and other debris are being expelled from the device differently than before. This can cause the work area to be messy and user might not be able to complete the lawn mowing job. Be sure the engine is turned off before replacing this chute.This discharge chute is sold as a single piece and is sourced directly from the manufacturer. This part is an OEM replacement part that is meant to fit on different models of lawn mowers. Refer to the owner's manual before attempting this repair.

This idler arm is a genuine Husqvarna part, sold individually. This idler arm can be used as a replacement part in a lawnmower. This part secures the steering linkage while allowing it free range of motion. If the idler arm is punctured, dented, cracked, chipped, scraped, warped, or eroded, it should be removed and replaced by this genuine OEM replacement part as soon as possible in order to ensure safe continued use.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This idler arm is compatible with the following outdoor appliance brands: Husqvarna.

This is a spring that is used on many Husqvarna lawnmowers. The component is located in the middle of the retainer and at the drive disk on the rear-wheel drive system. The main purpose of the spring is to ensure proper tension is applied between the drive disk and the pinion gear. Through time or wear and tear, this spring can become damaged or break. If this occurs, the component will need to be replaced in order to use the lawnmower.A screwdriver, socket set, and work gloves will be needed to replace this part. Make sure the lawnmower is powered off and the spark plug has been removed. Take the lawnmower and place it on a solid and sturdy surface while working on it. Remove the wheel where the spring is broken and take out the pinion, pawl, and spring. All of these items can be replaced or the pawl and pinion can be reused with the new spring.This spring is made for several lawnmowers manufactured by Husqvarna. The component is sold on an individual basis. This is a genuine OEM replacement part that is sourced directly from the manufacturer.

This part is a replacement deck lift shaft spring. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part will replace a broken, bent, or otherwise defective deck life shaft spring in lawn tractors.The deck lift shaft spring is part of the system that moved the lift shaft. This enables the user to adjust the lawn tractor's deck. With regular equipment use, this spring can become corroded, bent, stretched, or otherwise damaged. If this occurs, this part will need to be replaced. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this deck lift shaft spring, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality metal. This deck lift shaft spring can be used with lawn tractor models that have been manufactured by Husqvarna and Poulan. Sold individually.

This nose roller is a genuine Husqvarna part, sold individually. This nose roller can be used as a replacement part in a lawn mower. This part props the front of the mower deck up.The nose roller could be subject to damage in the form of puncturing, tearing, ripping, scraping, denting, or eroding; if any of these forms of damage prevent the nose roller from protecting the deck, the nose roller should be removed and replaced by this genuine OEM replacement part. Always unplug the appliance before performing any kind of repair or replacement.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This nose roller is compatible with the following outdoor appliance brands: Husqvarna, Jonsered, Craftsman, and Poulan.

This rod roller nose, also sometimes referred to as an axle, is a genuine Husqvarna part. It is a replacement part for lawn mowers.This part attaches to the deck of the mower and prevents it from running into the ground while in operation. This prevents damage to other parts of the mower and can also help prevent an accident. It is not uncommon for the rod roller nose to become damaged or break as a result of normal wear and tear, especially under heavy use or after several years.This rod roller nose is a genuine OEM part sourced directly from the manufacturer. It is sold individually. It is manufactured for compatibility with mowers made by Husqvarna and Poulan.

The washout port helps to make cleaning a mower deck easier and it is used on mowers and tractors. Users should wash the deck of the mower to reduce buildup. Doing so will help owners to extend the life of the mower deck. The washout port is the area that attaches to the deck of the machine. Owners can attach a hose and clean away grass and debris that have built up under the deck.The washout port is made from metal and is durable. However, there could still be a need to replace it in the event it becomes damaged or corroded. Replacement of the washout power is relatively simple. It will require the use of a socket set and a wrench set.This washout port is a genuine OEM replacement part for use with certain models of lawn tractors from Husqvarna, Craftsman, Jonsered, and Poulan. It is sold individually.

This part is a gauge wheel. A gauge wheel helps support the mower deck of lawnmowers and lawn tractors. The gauge wheel is also what allows the lawnmowers and lawn tractors to move.A new gauge wheel may be needed if the old one is physically broken or damaged in any way. The gauge wheel may need to be replaced after prolonged use due to build up of normal wear and tear. One of the most common ways that the gauge wheel is broken is when the lawnmower or lawn tractor runs over a small stump or concrete. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine Husqvarna part and is an OEM part sourced directly from the manufacturer. It is sold individually. The gauge wheel is compatible with lawnmowers and lawn tractors manufactured by Husqvarna, Rigid, Poulan, and Jonsered.

This spindle shaft assembly is a genuine Husqvarna part, sold individually. This spindle shaft assembly can be used as a replacement part for a lawn mower. The purpose of a spindle shaft assembly is to maintain the placement of the spindles so they can freely rotate along with the blades of the appliance.Damage could come in the form of puncturing, scraping, cracking, denting, or erosion. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This spindle shaft assembly is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Poulan, Ariens, and Dixon.

This stud fastener is a genuine Husqvarna part, sold individually. This stud fastener can be used as a replacement part for a lawn mower. The purpose of a stud fastener is to fasten components to one another with a threaded bar that attaches at its ends to make a bolt.The stud fasteners within a lawn mower might have to be replaced if one or more of them are lost, misplaced, or worn out over time. This could occur if the stud fasteners fall out of the appliance, in which case they should be immediately replaced by this genuine OEM replacement part, or if they are stripped over time from general wear and tear from long-term use. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This stud fastener is compatible with the following outdoor appliance brands: Husqvarna and Poulan.

This replacement part is a hair pin and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Hair pins are an important part of many different types of machinery as they hold other parts in place and secure. A new hair pin might be needed if the current ones are loose or missing. It is common that hair pins might become stripped overtime and will need to be replaced. Be sure to double check the size of the hair pin as many places on lawn equipment will require different sizes of this part. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

The shoulder bolt has many applications in lawn equipment, but this model is designed for use in riding mowers. The job of this shoulder bolt is to keep the gauge wheel in the correct place. This part is often referred to as the roller bolt. Over time, this bolt can become worn from regular use. The threads on the bolt may strip or it may become damaged as a part of other repairs or incidents. In any situation, the best option would be to replace the bolt with this genuine OEM model from Husqvarna. This shoulder bolt is manufactured to exact specifications for replacement in the gauge wheel. This part is designed for use with riding lawn mowers from Poulan, Husqvarna, and Jonsered. It is compatible with several machines from these brands. This shoulder bolt is made of durable metal and requires a wrench for installation. It is sold as a single unit and does not include any other parts. Always wear gloves when replacing parts for hand protection. Be sure to disconnect the spark plug prior to doing engine work. This part includes a one-year warranty from the manufacturer.

This genuine Husqvarna bolt and washer replacement part is specifically engineered to hold and secure the lawnmower blade in place. The bolt is threaded while the washer has a curved or rounded headed. A washer is needed for even load distribution of the threaded bolt. Fastening the bolt without the fastener may cause stress to the material it's driven into. One of the warning signs that the bolt and washer are broken is if the lawnmower blade doesn't rotate properly. Instead of moving in one circular motion, it turns erratically and goes up and down. In some cases, it will make a loud grinding noise during cutting. The lawnmower blade may even fly out from its normal position. Replacing the worn-down bolt and washer is fast and straightforward. First, shut down the engine and let it cool. Then, take out the spark plug and turn the mower on its side. Use a socket to remove the old bolt and washer. Then, grab the replacement and insert it through the blade's hole. Tighten it using the socket. This original Husqvarna bolt and washer is only suitable for lawnmowers made by Husqvarna, Craftsman, and Weed Eater. It is also compatible with some Dixon and Poulan lawnmowers. This bolt and washer replacement is sold individually.

This is the replacement washer head screw for a lawnmower or lawn tractor. It is black in color and is roughly 1.5 inches in length. With its hexagonal head and washer face, it is usually used as a fastener in outdoor power tools. It is self-tapping, meaning it can tap its own threads when screwed into either plastic, wood, or metal. When used with lawn tractors and lawnmowers, this screw is commonly employed for securing the mandrel housing to the mower deck. Replace the washer head screw if the old screw is damaged or missing. First, a pilot hole should be made that's slightly smaller than the diameter of this screw before driving it with a screwdriver. This is also a thread-forming type of self-tapping screw, and it does not have a pointed tip. It is compatible with specific products from major brands like Ariens, Craftsman, Husqvarna, Murray, Poulan, Ryobi, and Weed Eater. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.

This part is a nyloc nut. This specific nut is used in many different applications depending upon the outdoor power equipment machine that it is used on. This nut has a nylon collar insert that resists turning when it has been threaded on correctly. The nyloc nut is a type of lock nut, which prevents loosening when it's exposed to vibrations. It helps fasten parts together.A new nyloc nut may be needed if the original one has been broken, damaged, or lost. If the nyloc nut is no longer staying in place when it is exposed to vibrations and the operator can notice the parts loosening, then the nyloc nut will need to be replaced.This is a genuine OEM part sourced directly from Husqvarna. It is sold individually. This nyloc nut is used on snowblowers that are manufactured by both Husqvarna and Craftsman.

This top lock flange nut is a genuine Husqvarna part, sold individually. This top lock flange nut can be used as a replacement part for lawn mowers. The purpose of a top lock flange nut is to provide a fastening component, in conjunction with a bolt, through which two parts can be affixed to one another through clamping and rotation.The top lock flange nut is a small fastening component that can be easily lost and misplaced. If components come loose as a result of a lost top lock flange nut, the component should be replaced by this genuine OEM replacement part. Additionally, over time, a top lock flange nut can be stripped or eroded beyond functionality, in which case the component should be replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This top lock flange nut is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Dixon, Poulan, and Aries.

This replacement part is a flange nut. It is a genuine replacement part made by Husqvarna. This part is small yet extremely important to the operation of many different appliances and machines. Nuts are able to hold other parts in place and secure them tightly so that everything can operate smoothly and efficiently. A new flange nut might be needed if the current ones are damaged in any way or even missing. This repair should be fairly easy and only require a screwdriver or pliers if the previous part is lodged in place. It is possible that nuts can become stripped or stuck over time and should be replaced when and if this occurs. Be sure the engine is completely powered down before starting a repair. This part is sold individually and is a genuine OEM replacement part sourced directly from the manufacturer.

This hex nut is a genuine Husqvarna part, sold individually. This hex nut can be used as a replacement part in a lawn mower. The purpose of the hex nut in a lawn mower is to secure a component to another component in conjunction with a bolt so that, during the standard operation of the lawn mower, the components do not move from their position of stable placement.The hex nut in a lawn mower is a small component, and its size means that it can be easily lost, misplaced, or stripped from general wear and tear with long-term use. The hex nut could also be damaged as a result of a collision with a hard object such as a rock or a curb. If any of this occurs, the hex nut should be replaced by this genuine OEM replacement part as soon as possible.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This hex nut is compatible with the following outdoor appliance brands: Husqvarna, Poulan, and Weed Eater.

This part is a genuine OEM replacement mandrel spacer washer usually used to line up drive pulleys on lawn tractors or riding mower engines. The drive pulley is an integral part of the transmission. As a type of washer, a mandrel spacer helps to distribute weight and pressure so that the link does not crack or bend. Compared to standard washers, though, mandrel spacers are quite thick, so they can take more of a load. The best time to replace a mandrel spacer washer is when making repairs to the drive pulleys. These parts take a lot of wear and tear and can corrode the connection over time. To prevent this from happening, replace the mandrel spacer washer as soon as it starts to look worn out or when conducting regular maintenance. This mandrel spacer washer is a top of the line replacement part for Ryobi, Jonsered, Weed Eater, Poulan, and Husqvarna engines. As such, this part comes sourced directly from its original manufacturer. This spacer washer does not ship with any additional hardware.