Mtd Engine Parts

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

This is a genuine replacement shoulder screw that is compatible with select models of lawn tractors. The shoulder screw has multiple applications in lawn tractors, where it is typically used as some kind of axle for wheels or other components. Over time, this type of screw can become worn from repetitive motion or the threads can start to strip. If the screw fails or is unable to work effectively, it can affect whatever it is responsible for securing or holding, as well. This could result in the entire machine not working until a replacement is made. This is a genuine manufacturer's replacement manufactured by MTD. It is compatible with their lawn tractors as well as those from Yard Machines, Troy-Bilt, Yard Man, Husky, and Cub Cadet. The screw is made of durable metal and is sold as a single unit. This is considered specialty hardware and is also sometimes referred to as a shoulder bolt.

The recoil starter assembly starts the engine by using the grip to pull the rope, which activates the starter pulley and spring, causing the flywheel to rotate and start the engine. Over time, the starter spring can become stretched, causing the rope to seize up or fail to retract. The housing itself could also become damaged. It’s often easiest to replace the entire recoil starter assembly with this OEM model rather than individual components. The installation can be done quickly with a screwdriver and wrench by removing the three bolts that hold the assembly in place. This genuine OEM part is manufactured by MTD. It fits lawn mowers, tillers, log splitters, and other small engines made by MTD, as well as models from Bolens, Yard-Man, Yard Machines, Cub Cadet, Troy-Bilt, and Husky. This part includes the starter housing that protects the flywheel and other internal components, along with a starter pulley, spring, pull rope, and grip. The hardware required for this assembly is not included and must be purchased separately.

This air cleaner cover is designed to house the air filter on larger lawn equipment and other outdoor power tools. There is no aspect of small engine care more necessary than protecting the air that goes into the carburetor and cylinder from yard dust. Nothing is more incapacitating to a small engine than being clogged with dust, pollen, and other particulates that are invariably stirred up during landscaping work. While the air cleaner cover itself is not a moving part and would not seem to be subject to replacement, it is occasionally the case that, through extensive use or accidental contact, the cover becomes unable to shield the air filter within it. In these cases, it is essential to replace the cover with an OEM certified replacement cover that has been manufactured to the same specification as the original. Though replacing the cover itself is quite simple, it probably a very good idea to replace the air filters at the same time. If the cover is in need of replacement, it is quite likely the filters have been exposed to excessive amounts of particulate. This cover can be used on chippers, shredders, log splitter, mowers, and a variety of other small engine/large job equipment. Compatible brands include Troy-Bilt, MTD, Yard-Man, Yard Machines, and Cub Cadet.

This is a replacement carburetor assembly that is used on small engines found in many types of lawn and garden equipment. The carburetor is responsible for ensuring there is a proper fuel-air mix before the fuel is sent to the engine. This assembly is made from metal and features a plastic lever. The carburetors found in engines are durable, but this does not mean that they will not wear down over time. Eventually, they may need to be replaced. If they have become damaged and are no longer functioning properly, it could cause issues with the performance of the engine. They will need to be replaced. This genuine OEM replacement carburetor is sold individually. Buyers will need to purchase gaskets separately. The part works for wood chippers, tillers, leaf blowers, and other small engines. Brands with models compatible with the carburetor include Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, Yard-Man. When purchasing, buyers should make sure that this carburetor is correct for their make and model of engine.

The replacement screw seen here is made from high-quality, durable metal. It is an identical replacement for a faulty screw in many types of lawn and garden equipment. The screw features a hex-bolt shaped head and is used for various applications in the machines. Owners will want to refer to diagrams of their model to ensure the correct application for the screw. A screw may need to be replaced for any number of different reasons. In some cases, the screw could become lost when making other repairs to the machine. It could also become bent or the threads could be damaged. Corrosion is also a possibility over time. Replacing the screw is typically considered a fast and easy repair. The screw is a genuine OEM replacement part that is sold individually. The screw can be used for many models of snowblower, lawnmower, chainsaw, tiller, string trimmer, log splitter, edger, and wood chipper. Compatible brands include Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

This recoil starter assembly is a genuine MTD part, sold individually. This recoil starter assembly can be used as a replacement part for a tiller. The recoil starter assembly comes with all of the necessary components and fasteners required to replace a recoil starter. The recoil starter is a crucial part of the pull-start mechanism of a tiller, by which the engine of the tiller is powered on when the operator engages the pull-start. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This recoil starter assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Yard Man, Yard Machines, and Huskee.

This choke bracket is a genuine OEM part sourced directly from the manufacturer for use on snowblowers. The choke control bracket opens or closes the choke plate in the carburetor to help start the engine. The choke should be closed when getting it ready to work. Closing it shuts the air intake and keeps the gas mixture richer, which helps the engine fire up when it is cold. If the choke bracket is rusted or broken and is working, the choke may not work correctly. The engine may not start or may run roughly when it does start. If this happens, the choke bracket should be replaced.Before replacing the choke bracket, remove the spark plug and empty the gas from the snowblower. Wear safety gloves and safety glasses. Locate the choke and remove the screws holding it in place. Remove and discard it and install the new bracket. Use the screws from the original bracket to secure the bracket. Reinstall the fuel and spark plug. This choke bracket is a silver metal part that is sold individually; it does not come with screws or bolts. It is designed for use in snowblowers manufactured by Craftsman and MTD.

This carburetor insulator is a genuine MTD replacement part for appliances with small engines, such as lawn mowers, lawn tractors, lawn trimmers, snowblowers, chipper shredders, tillers, and leaf blowers. The purpose of a carburetor insulator is to keep the heat of the running engine away from the carburetor, which combines the air and fuel that ignites the engine. This keeps the engine from overheating and suffering damage as a result.While there is a chance that a damaged carburetor insulator could prevent the engine from igniting altogether, it is more likely that a damaged carburetor insulator will allow for unmetered air leaks into the carburetor. Unmetered air leaks will cause the engine to take in more fuel, reducing the fuel economy of a small engine appliance. For this reason, if the symptoms align with a diagnosis of a damaged carburetor insulator, it must be individually replaced as soon as possible before using the small engine lawn appliance again.This carburetor insulator is compatible with the following brands: MTD, Cub Cadet, Yard Machines, and Craftsman.

This carburetor insulator is a genuine MTD part, sold individually. This carburetor insulator can be used as a replacement part for a lawn mower. The purpose of the carburetor insulator is to prevent overheating in the carburetor.If the carburetor is frequently overheating, the carburetor insulator should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This carburetor insulator is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Yard Machines, and Huskee.

This part is a replacement rocker arm stud. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part is intended for use as a replacement for a broken or defective rocker arm stud on various types of outdoor small engine power equipment. This rocker arm stud works by securing the cylinder head. The rocker itself slides over the stud and is then held securely by the nut that locks it into place. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this rocker arm stud, the appropriate owner's manual and equipment diagrams should be referenced. This rocker arm stud is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with lawnmowers, blowers, and tillers that have been manufactured by MTD, Yard Machines, Cub Cadet, Bolens, Husky, and Troy-Bilt.

This is a genuine OEM replacement fuel bowl bolt for a snowblower, tiller, or chipper engine. The fuel bowl is a part of the fuel filtration system designed to prevent sediment from clogging up the carburetor. Fuel moves from the fuel tank and passes through the fuel bowl to catch any debris. It is essentially a particle filter. This bolt mounts the fuel bowl in place. The two most likely reasons why a fuel bowl bolt might need replacing are general wear and tear or loss. This bolt is located fairly close to the outside of the engine, making it more susceptible to the elements. Over time, the bolt may corrode and will need replacing. If lost while making a repair to the fuel bowl itself, the fuel bowl bolt will need to be replaced. Use a wrench to make the repair. This fuel bowl bolt is a top of the line replacement part for Bolens, Yard Machines, MTD, Troy-Bilt, Huskee, and Yard Man appliances. This part does not include any additional hardware, as it ships individually.

This replacement part is a flange bolt and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This flange bolt is small but an important part to many machines and appliances. Bolts are able to keep things and place and hold other parts secure so that the entire appliance is able to operate smoothly. A new flange bolt might be needed if the user notices that the current one is damaged or missing. This could mean that parts of the appliance are coming off or becoming loose overtime. This replacement should be fairly simple and should only require a screwdriver and possibly pliers if the previous bolt is lodged in the appliance. Be sure to reference the specific owner's manual before replacing this part. This bolt is sold as a single piece. This is a genuine OEM part and is sourced directly from the manufacturer.